The invoice for a screen changer has three separate lines and buyers usually compare only the first. There is the unit itself, there is the hydraulic or drive package that makes it automatic, and there is the screen media and tooling that has to be replaced every time the filter blocks. A continuous unit that costs three times a manual one can still be the cheaper arrangement over three years, and a manual one can be the cheaper arrangement over one.
The other side of the ledger is the scrap. A mismatched screen changer is reported to raise the scrap rate by 15–30%, and continuous filtration is reported to cut energy use by about 8–12%. On a line running at 0.26–0.50 kWh/kg, that energy figure alone changes the arithmetic.
The three lines on the invoice
- Equipment, then the automation package, then the consumables that every change needs.
- Published 2026 export units run from US$500 to US$2,000; hydraulic double-station units are listed at CNY 10,000–16,800.
- A mismatched filter is reported to raise scrap rate by 15–30% — usually the largest single number on the line.
- Continuous filtration is reported to cut energy use by about 8–12%, against a specific energy of 0.26–0.50 kWh/kg.

The cost side: three separate lines on the invoice
When buyers compare screen changer quotations they usually compare the machine price, which is the smallest of the three numbers that matter.
The first line is the equipment itself. Chinese supplier listings for 2026 put manual units at CNY 5,000–20,000, hydraulic units at CNY 10,000–16,800 and continuous systems at CNY 50,000–200,000, with export listings for hydraulic units at US$500–2,000.
The second line is the consumables: screen packs, and the labour to change them. On a line running three to four hours per screen, the annual screen consumption is a recurring operating cost and belongs in the calculation.
The third line is the energy. A screen that fouls early raises the pressure the extruder works against, and pressure against resistance means more heat input for the same output. Continuous filtration is reported to reduce energy use by roughly 8–12%, which on a 500 kg/h line at 6,000 hours a year is a meaningful number.
The saving side: what a wrong filter costs

The bigger number is on the scrap side, and it is where the return on filtration is actually made.
Industry selection guidance reports that a mismatched screen changer can raise the scrap rate by 15–30%. On a single screw line tolerating about 2% non-melting contamination at 60–80 mesh, exceeding that level means the screen blinds within hours, die pressure swings, and the pellet falls out of specification.
Put that against the value of the product. A contamination event that puts a hundred kilos of off-specification material into a bag is a hundred kilos sold at the price of scrap, and it is also a hundred kilos the customer will not buy twice.
There is a third saving that is easier to miss: the machine that keeps running is the machine that does not need a motor replacement. Screws fail from degradation and from the heat of working against a fouled path, and both are preventable by keeping the melt clean.
Working out whether continuous filtration pays for itself
The calculation is straightforward once the four inputs are honest: the price difference between the architectures, the annual screen consumable cost, the hours of production the changeover currently costs, and the scrap rate the current filtration is causing.
Take a typical case. A 300 kg/h line running two shifts changes the screen manually every four hours. Each change costs 15 minutes of stopped production. At a conservative 100 kg/h of saleable value, that is 25 kg lost per change, 12 changes a day, and roughly 8.7 tonnes a month. At the material prices these lines see, that is a direct, recurring cost that a hydraulic unit removes almost entirely, for a capital difference of a few thousand dollars.
Now add the scrap side. If the current filter is undersized for the material and 2% of production is going out of specification, that is a much larger number than the changeover. Continuous filtration earns its price here, and it is the changeover that stops being the argument.
The honest caveat is that none of this applies to a clean-feed small machine. On a 100 kg/h single screw running in-house scrap, a manual basket is entirely adequate, and the calculation should say so.
Where the money should actually go
There is a consistent ranking in the conversations we have with plant managers, and it is not the one most people expect.
Filtration comes after moisture. Contamination is far cheaper to remove in a wash tank than in a screen pack, and the threshold is explicit: above 8% contamination, washing is cheaper than filtering, and sand and paper belong in a wash tank rather than in your screen.
Filtration also comes after bulk density control. If the feed is fluffier than the machine can swallow, the pressure swings for reasons that have nothing to do with the filter, and no screen changer will fix it.
And it comes after the process settings. Residence time, melt temperature and venting determine how much carbonised polymer there is to filter in the first place. A correctly specified filter on a badly controlled process will still foul early — the filter is the last line of defence, not the first.
Annual cost comparison framework
The comparison below is set up so the scrap and energy columns can be filled in with your own figures.
| Cost line | Manual changer | Hydraulic changer | Continuous changer |
|---|---|---|---|
| Equipment | CNY 5,000–20,000 | CNY 10,000–16,800 | CNY 50,000–200,000 |
| Changeover time | 10–15 minutes each | Seconds | No production stop |
| Production lost at 300 kg/h | ≈25 kg per change | Negligible | None |
| Energy effect | Baseline | Similar | Reported 8–12% lower use |
| Scrap risk | Higher if the filter is undersized | Lower | Lowest on contaminated feed |
Questions buyers ask about this machine
Q1: Is a screen changer worth it on a small single-screw line?
On a small line running clean in-house scrap, usually not as a continuous system — a manual basket is adequate. The answer changes as soon as the material carries contamination or the changeover stops being cheap. The calculation above shows the crossover: it is driven by changeover time and scrap rate, not by machine size.
Q2: How much does a screen changer add to the cost per tonne?
On a clean-feed manual setup, very little beyond the consumables. On a contaminated line it is the difference between producing at specification and producing at a discount. The reported 15–30% scrap increase from a mismatched filter is the number to work from, because it applies to every tonne rather than to the changeover.
Q3: Does filtration affect energy consumption?
Yes, in two directions. A fouled filter raises the pressure the extruder works against, and pressure against resistance means more heat for the same output. Continuous filtration is also reported to reduce energy use by roughly 8–12%, because the melt path runs at a consistent pressure instead of a rising one.
Q4: What should I fix first if my pellets are contaminated?
Moisture and bulk density before filtration. Material above 8% contamination should be washed rather than filtered, and a feed that is fluffier than the machine can swallow produces pressure swings that look like a filter problem and are not.
Also worth reading: auxiliary equipment index, FAQ on contamination limits, the 12-platform comparison, two-stage granulating line and plastic recycling equipment.
Three more notes from the same test floor: Screen Changer for Plastic Extrusion: What It Does, Manual, Hydraulic or Continuous Screen Changer: Which?, Screen Changer Filter Area: Calculation and Pressure and Screen Change and Maintenance Routine for Plastic Extruders.
About the author
Zhou Gong (周工) is a recycling machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong, where 30-plus staff work across 18,000 m² and 12 machine platforms covering 100 to 3,000 kg/h. The calculation I do first is never the machine price. It is the scrap rate against the pellet price, because that is the number that decides the answer. Every figure used here has been measured on a machine or taken from a dated published source, not from a brochure.
Send the material form, the contamination level and your target output to our engineering team and you get a model and a price range within one working day. A test run on 10–20 kg of your own material is free, and if the measured output misses the agreed figure by more than 5%, the deposit is refundable.