TL-FK · Recycling lines
Flakes Pelletizing Machine
Force-fed single screw for washed HDPE and PP flake — 300 to 1,000 kg/h at 0.26–0.36 kWh/kg.
- Output
- 300–1,000 kg/h
- Screw diameter
- 150 / 165 / 180 mm
- Feedstock
- Washed HDPE, PP, PS flake, 8–30 mm
- Indicative price
- US$28,000 – 72,000
What this machine does
Flake is the easiest feedstock to run and the hardest to run well. It flows, so the screw starves; it carries surface water, so the melt foams. The TL-FK solves the first problem with a force feeder whose auger speed is slaved to the screw torque, keeping the flights 85–95% full instead of half empty.
For the second problem there are two vacuum vents and a 3 m pre-heating section, so moisture flashes off before the compression zone. On bottle flake that is worth 8–12% output; on cold-washed flake with 4% water it is the difference between running and not running.
Filtration is where flake lines differ most. Bottle flake with labels and caps needs 100 mesh; agricultural drum flake with sand needs 80 mesh and a larger screen area. We size the changer by dirt load, not by output, because a changer that blinds in 20 minutes makes a 1,000 kg/h line behave like a 600 kg/h one.
Models and output
| Model | Output | Screw diameter | Main motor | Filtration | Footprint | Weight |
|---|---|---|---|---|---|---|
| TL-FK-150 | 300–450 kg/h | 150 mm | 90 kW | 100 mesh | 8.0 × 1.8 × 2.3 m | 5.5 t |
| TL-FK-165 | 500–700 kg/h | 165 mm | 160 kW | 80–100 mesh | 9.0 × 2.0 × 2.5 m | 7.8 t |
| TL-FK-180 | 800–1,000 kg/h | 180 mm | 250 kW | 80 mesh | 10.0 × 2.2 × 2.7 m | 11.2 t |
Output figures refer to LDPE film at 85% bulk density with 3% moisture. Actual output depends on feedstock, flake size and filtration.
Engineering highlights
- Force feeder with torque-following auger speed: flights stay 85–95% full
- Two vacuum vents plus 3 m pre-heat: 4% moisture handled without a dryer
- Lowest specific energy in the range: 0.26–0.36 kWh/kg
- Screen changer sized by dirt load, up to 100 mesh on bottle flake
- Wear-resistant 38CrMoAlA screw with optional bimetallic barrel
- Compact footprint: 8–10 m for the whole line including cutter
How the line works
Force feed
A vertical auger pushes flake into the screw; torque feedback sets the auger speed.
Pre-heat and vent
A 3 m feed section dries the flake; two vacuum vents remove the remaining volatiles.
Filter
80–100 mesh packs in a double-piston changer hold back labels, sand and unmelt.
Cut and dewater
Water ring cutting at 2.5–4 mm, then dewatering to below 0.3% moisture.
Where it runs
- HDPE bottle and cap flake
- PP crate and container flake
- PS and ABS appliance flake
- Washed agricultural drum flake
- Injection plant regrind
Options and upgrades
- Automatic back-flush changer for 120 mesh
- Melt pump for ±0.4% pellet weight
- Hot-wash flake drying module upstream
- Colour masterbatch dosing unit
- Bagging line with metal detection
Questions buyers ask
Do I need a dryer before this machine?
Normally no. Two vacuum vents handle surface moisture up to 4%. Above that, a mechanical dewatering press or a hot-air dryer pays for itself in output within a few months, because every 1% of water costs roughly 3% of capacity.
What pellet size should I sell?
3–3.5 mm is the default for injection and blow moulding. Film and cable customers often ask for 2.5 mm. Below 2 mm the cutter output drops and fines increase, so only do it when the buyer specifies.
How many hours can it run continuously?
The line is designed for 24/7 duty with a 20-minute screen change every 3–4 hours and a blade check every 8 hours. Continuous campaigns of 30 days are normal on bottle flake.
Related machines
Other platforms in the range
TL-SJExtrusion granulating
Single Screw Plastic Granulator
The workhorse pellet extruder for PP, PE and ABS regrind — 150 to 700 kg/h with one hardened screw.
- Output
- 150–700 kg/h
- Indicative price
- US$12,500 – 46,000
TL-GPLRecycling lines
Plastic Granules Production Line
Turnkey washing and pelletizing: from baled bottles or film to bagged granules, 500 to 3,000 kg/h.
- Output
- 500–3,000 kg/h (finished pellets)
- Indicative price
- US$85,000 – 260,000
TL-WRPelletizing systems
Water Ring Pelletizer
Die-face cutting inside a water ring — 100 to 1,000 kg/h in 6 m of floor space, no strand bath.
- Output
- 100–1,000 kg/h
- Indicative price
- US$18,500 – 52,000
Need a line sized to your material?
Flakes Pelletizing Machine
Send the polymer, contamination level and target output. You get a model recommendation, power estimate and price range within one working day.
- Reply within 1 working day
- Sample test before you commit
- Factory visits and live video trials by appointment.
Tell us what you need to granulate
Six fields is enough for a first recommendation. Drawings, layout and a firm price follow after the material sample is tested.