CE marked · ISO 9001:2015 · 18-month warranty

· products · By

Manual, Hydraulic or Continuous Screen Changer: Which?

Manual, hydraulic or continuous screen changer: the three architectures compared on downtime, filtration quality and what each can realistically hold back.

There are three screen changer architectures and they differ far more in downtime than in price. A manual changer costs the least and stops the line when the screen blocks. A hydraulic double-station changer removes the screen change from the critical path but still interrupts the melt. A continuous changer keeps the melt moving while the screen is changed, and it is the only one of the three that suits a line that cannot stop.

Published 2026 export listings put a manual unit at CNY 5,000–20,000, a hydraulic double-station unit at CNY 10,000–16,800, and complete export units at US$500–2,000 each. The price gap looks small until you multiply a manual screen change by the number of people standing next to it.

Three architectures, three different business cases

  • Manual: cheapest, and every screen change is a line stop.
  • Hydraulic double-station: the screen change leaves the critical path; the melt still stops.
  • Continuous: no melt interruption at all, and the running cost is the equipment, not the labour.
  • A mismatched screen changer is reported to raise scrap rate by 15–30%; continuous filtration is reported to cut energy use by about 8–12%.
3D render of an orange TENGLONG machine with a feed hopper beside a white control cabinet and a green material hopper
3D render of an orange TENGLONG machine with a feed hopper beside a white control cabinet and a green material hopper. Used here as a visual reference for the three screen changer architectures. Rendering, not a photograph of a customer plant.

Three architectures, three different cost profiles

The screen changer decision is not really about filtration quality — all three types can filter to the same mesh. It is about how much production time you are willing to spend not producing.

A manual screen changer is a bolted filter basket. Changing the screen means stopping, opening, unbolting, replacing and rebolting. It is cheap — Chinese supplier listings in 2026 put manual units at CNY 5,000–20,000 — and it is entirely adequate on a small single-screw machine with clean feed, where the change interval is long and the tonnage at risk is small.

A hydraulic screen changer swaps the filter under pressure with a cylinder, typically in a few seconds, without opening the melt path. Published export listings put these at US$500–2,000 per unit, and Chinese hydraulic units at CNY 10,000–16,800. This is the standard on our single screw and two-stage platforms.

A continuous screen changer — dual-piston, rotary or backflush — filters without stopping at all: one position is on line while the other is swapped or cleaned. Chinese listings put continuous units at CNY 50,000–200,000, and the industry selection guides report longer filter life and roughly 8–12% lower energy use as the headline benefit.

The downtime arithmetic that decides it

Rendered scene of a TENGLONG workshop with a green machine and a group of visitors
Rendered scene of a TENGLONG workshop with a green machine and a group of visitors. Shown here as production context. Rendering, not a photograph of a customer plant.

Run the numbers on your own shift pattern. A manual change takes 10–15 minutes. A hydraulic change takes seconds. A continuous changer takes no production time at all, but changes how often the filter is touched.

On a 300 kg/h line at an average of 100 kg/h sale value, a 15-minute manual stop every 6 hours costs about 75 kg of production per event — roughly 300 kg a day, or about 25 tonnes a month. That is a number worth comparing against the price difference between a manual and a hydraulic unit.

The case for continuous filtration is different and stronger on contaminated feed. A mismatch between the filter and the material is reported to raise scrap rates by 15–30%; on a line running 8,000 hours a year, even a fraction of that is more than the cost difference between the architectures.

What each type can realistically filter

Architecture constrains filtration performance, not just convenience.

Manual units are typically single-position with no changeover during operation. They are fine for coarse screens on clean material, and unsuitable where the filter must be swapped every 30 minutes.

Hydraulic dual-station units keep one position on line while the other is offline for cleaning, which means the filter change itself costs no production time and the pressure drop during the swap is small. They handle 40–60 mesh reliably on single-stage duties.

Continuous systems — dual-piston, rotary or backflush — are the only ones that suit very fine meshes on dirty feed, because they can hold a second filtering stage in service while the first is cleaned. If your material carries more than about 8% contamination, this is where the difference shows.

Buying criteria beyond the price

Four specifications separate a good unit from a cheap one, and all four should be on the quotation.

Pressure rating. For high-viscosity compounds and reinforced materials, a hydraulic screen changer needs a burst pressure rating of at least 50 MPa; for general extrusion, 35 MPa is the reference floor.

Sealing. A dual-station unit with exposed seals will leak at the pressure the process needs. The better units wrap the plunger in a full seal so the melt path stays contained under load.

Temperature range. Standard units handle ordinary polyolefins. Polyamides and engineering grades need a high-temperature variant rated well beyond 280 °C.

Changeover control. Manual, differential-pressure triggered and timed automatic switching are all available, and the automatic modes are what make a continuous unit genuinely continuous.

Screen changer types compared

The three architectures below differ in what they cost to run, not only in what they cost to buy.

Type Changeover 2026 price band Best fit
Manual Stop, unbolt, replace — 10–15 min CNY 5,000–20,000 Small machines, clean feed, long intervals
Hydraulic dual-station Seconds, one position stays on line CNY 10,000–16,800; US$500–2,000 export Standard on single screw and two-stage lines
Continuous dual-piston / rotary / backflush No production stop CNY 50,000–200,000 Fine mesh on contaminated feed, 24/7 running

Common questions, with short answers

Q1: Is a hydraulic screen changer worth the extra cost?

On almost any machine that runs more than one shift, yes. The changeover drops from 10–15 minutes of stopped production to seconds, and the second station keeps filtering while the first is swapped. The published difference between a manual unit and a hydraulic unit is small; the production time it protects is not.

Q2: When does continuous filtration pay for itself?

When the filter is changed often enough that the changeover time dominates, or when contamination is high enough that a fixed screen cannot hold die pressure stable. Continuous systems are reported to cut energy use by roughly 8–12% as well, because the extruder runs at a consistent pressure rather than riding a rising one.

Q3: What mesh do I need for recycled material?

For a single screw handling about 2% non-melting contamination, 60–80 mesh. For a two-stage line on 5–8% contamination, 60–100 mesh with the second stage decoupled. Above 8% contamination, a finer screen is the wrong answer — washing the material is cheaper.

Q4: Does the screen changer need to match my extruder size?

Match it by filter area, not by nominal size. The working rule is area in cm² = melt flow in kg/h ÷ (filter factor 0.2–0.6 × material density). A 500 kg/h HDPE melt needs roughly 250 cm². A screen changer that is too small for the flow will read high pressure permanently and need constant attention; one that is oversized costs more without buying anything.

Further reading on this site: auxiliary equipment index, twin screw extruder line, the 12-platform comparison and FAQ on contamination thresholds.

The rest of this series covers the same equipment from different angles: Screen Changer for Plastic Extrusion: What It Does, Screen Changer Filter Area: Calculation and Pressure, Screen Change and Maintenance Routine for Plastic Extruders and Screen Changer Cost: What It Costs and What It Saves.

About the author

Zhou Gong (周工) is a recycling machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong, where 30-plus staff work across 18,000 m² and 12 machine platforms covering 100 to 3,000 kg/h. I ask one question above all others: how many minutes does the line stand still for a screen change, and who is standing there when it does. Every figure used here has been measured on a machine or taken from a dated published source, not from a brochure.

Send the material form, the contamination level and your target output to our engineering team and you get a model and a price range within one working day. A test run on 10–20 kg of your own material is free, and if the measured output misses the agreed figure by more than 5%, the deposit is refundable.

Related reading

العربيةAR