CE marked · ISO 9001:2015 · 18-month warranty

Equipment index · 14 washing and feeding terms

Washing line and feeding equipment

The upstream half of a recycling line: remove labels, separate by density, wash off glue, then get moisture below 2% before the flake ever reaches the screw.

14 defined terms on this page, each with its own citable definition.

Terminology

Washing and separation

Density separation removes cap and label polymers; friction and hot washing remove glue, soil and oil. Skipping either one simply moves the contamination to the screen changer.

PET bottle washing line

PET 瓶清洗线

The complete bale-to-clean-flake chain: label removal, crushing, float-sink separation, friction washing, hot washing, rinsing, dewatering and drying.

See the matching machine

PET flake washing machine

瓶片清洗设备

Buyer phrasing for the washing stages applied to already-crushed flake, usually quoted as a group rather than as one machine.

See the matching machine

Friction washer

摩擦清洗机

A high-speed paddle shaft that scrubs flake against itself and a screen to strip glued labels, sand and surface dirt.

See the matching machine

Floating and sinking tank

浮洗槽 / 沉浮分离水槽

A water bath that separates polymers by density: PP and PE caps float, PET and PVC sink. The cheapest contamination control in a washing line.

See the matching machine

Hot washing machine

热洗机

Heated caustic or detergent bath, typically 80–90 °C, that dissolves hot-melt glue and removes oil from post-consumer flake.

See the matching machine

Label remover

脱标机

Strips sleeve and paper labels from whole bottles before crushing, so label film does not end up as fine contamination in the flake.

See the matching machine

Terminology

Dewatering, drying and transport

Residual moisture turns into steam in the barrel and shows up as foaming, poor pellets and IV loss. This is the stage most often undersized.

Dewatering machine

脱水机

Mechanical water removal after washing, taking free water off flake before thermal drying or the extruder vent.

See the matching machine

Centrifugal dewaterer

离心脱水机

A high-speed rotor that spins water off flake through a perforated screen; commonly brings film flake below 2% moisture in one pass.

See the matching machine

Squeezing machine

挤干机

A screw press that squeezes and partly densifies washed film, replacing a centrifuge where light flexible feed holds too much water.

See the matching machine

Dryer

烘干机

Hot-air or dehumidified drying of flake or pellets. PET for bottle-grade reuse needs desiccant drying to roughly 50 ppm to protect intrinsic viscosity.

See the matching machine

Conveyor

上料输送机

Any belt, screw or pneumatic transfer between washing, drying and pelletizing stages; sizing it to peak throughput avoids upstream backups.

See the matching machine

Belt conveyor

皮带输送机

A flat belt for bales, bottles and bulky scrap before the crusher, often fitted with a metal detector or sorting station.

See the matching machine

Terminology

Feeding the extruder

Low-bulk-density film and flake will not fall into a standard hopper. Force feeding is what turns a washing line into a stable pelletizing line.

Forced feeder

强制喂料机

A rotating screw or crammer that pushes light flake into the extruder feed throat, holding a constant melt pressure at the die.

See the matching machine

Screw feeder

螺旋上料机

A metered screw that moves and doses flake or powder from a hopper into the next stage, often combined with gravimetric dosing on compounding lines.

See the matching machine

Questions

What buyers ask next

Each answer is written to stand on its own when quoted.

Why does moisture matter so much before extrusion?

Water flashes to steam in the barrel. On PET it hydrolyses the polymer and lowers intrinsic viscosity; on PE and PP it causes foaming, holes and unstable strands. The practical target is below 2% moisture after dewatering and drying, and about 50 ppm for bottle-grade PET.

Can I skip the washing line for in-house scrap?

Yes, for clean, known, dry in-house sprues and offcuts: go straight to the crusher and the granulator. Washing is for post-consumer material with labels, glue, soil or mixed polymers.

Continue

Related machines and equipment indexes

Follow the equipment chain, or open the machine pages for specifications and price ranges.

Next step

Not sure which term fits? Describe the material instead

Polymer, form, contamination, target output, voltage and country are enough for a model recommendation within one working day.

Tell us what you need to granulate

Six fields is enough for a first recommendation. Drawings, layout and a firm price follow after the material sample is tested.

Used only to answer this enquiry. No lists, no resale.

العربيةAR