CE marked · ISO 9001:2015 · 18-month warranty

33 questions

Plastic granulator questions, answered directly

These are the questions buyers actually send us, in the order they usually arrive: what machine, what output, what power, what pellet, what price.

Choosing a machine

How do I choose the right plastic granulator?

Choose by feed form first: film and bags need a compactor, rigid flake needs a force feeder, lumps and purging need a two stage line. Then add dirt load: below 2% contamination a single screw works, 2–8% needs two stage venting, above 8% needs washing first. Output and motor size come last, because an oversized machine on a difficult feed is worse than a correctly sized one.

What is the difference between a granulator and a pelletizer?

In everyday trade usage they overlap. Strictly, a granulator reduces scrap size and a pelletizer forms pellets; a plastic granulator usually means the whole machine that melts and cuts, while a pelletizer can mean just the cutting head. When specifying, describe the feed and the output — the names vary by region.

Single screw or twin screw — which do I need?

Single screw if you are recycling one or two known polymers without fillers. Twin screw if you are making a formulation: filler above 15%, glass fibre, flame retardant, or colour that must disperse below 20 µm. Twin screws cost 2–3 times more per kg/h, so do not buy one for plain regrind.

Do I need a crusher, a washer and a dryer as well?

For post-consumer material, yes: crush to 25–30 mm, wash to below 0.5% contamination, dewater to below 2% moisture. For clean in-house scrap, none of the three is needed. For washed flake bought from a supplier, only a hopper dryer is sometimes required.

Can one machine handle PP and PE on different days?

Yes. PP runs 10–15 °C hotter than LDPE; store both recipes in the PLC and the change is a five-minute temperature ramp plus a purge. What you cannot mix is colour: dark to light takes 40–60 minutes of cleaning.

What is the smallest machine you make?

The TL-PM-80, 100–150 kg/h with a 37 kW motor. The TL-MB-35 masterbatch line goes down to 20 kg/h. Below that, batch sizes are too small to fill the barrel and material loss exceeds the value of the batch.

Can you test my material before I order?

Yes. Send 10–20 kg to the factory and we run it on a comparable machine, then send video, measured output, specific energy and pellet photos. The test is free; you pay the freight. Customers are also welcome to attend the trial in person or by video call.

Output and performance

Why is my actual output lower than the catalogue figure?

Catalogue figures assume 85% bulk density, 3% moisture and moderate contamination. Wet film at 60 kg/m³, flake with 8% water or a 120 mesh screen can each cut output by 20–40%. The fix is usually upstream dewatering or a coarser screen, not a bigger motor.

How is output measured — before or after the cutter?

We quote finished, bagged pellets, averaged over four hours, which is 3–6% lower than extruder throughput because of fines, purges and start-up. If a supplier quotes screw throughput, the numbers are not comparable.

What is specific energy and why does it matter?

Specific energy is kWh consumed per kg of pellet. Our lines run 0.26–0.50 kWh/kg depending on polymer and moisture. On a 500 kg/h line running 6,000 hours a year, a 0.05 kWh/kg difference is 150,000 kWh — usually more than the price gap between a cheap and a good machine.

Can it run 24 hours a day?

Yes. The line is designed for continuous duty with a 20-minute screen change every 3–4 hours and an 8-hourly blade check. Keep one spare screw, one die plate and two screen packs on site and unplanned stops stay under 2%.

How long does start-up take each morning?

Twenty-five to forty minutes from cold: 20 minutes of barrel heating to set point, then a 5-minute purge and 5–10 minutes to stabilise pellet size. A line left in standby at 120 °C starts in 10 minutes.

Materials

Can the machine process PVC?

Yes, with a dedicated configuration: corrosion-resistant screw and barrel, lower compression ratio, 160–190 °C melt and no long residence at temperature. PVC needs a machine that is either run continuously or purged thoroughly before stopping, because stagnant PVC degrades and releases HCl.

What about PET, PA or other hygroscopic polymers?

They need drying first: PET to below 50 ppm after crystallization, PA to below 0.1%. Without it, PET loses 0.01 dl/g of IV per 100 ppm of moisture and PA develops bubbles and weak pellets. Add a dehumidified dryer, not just a hot hopper.

Can it handle heavily printed film?

Up to about 5% ink with two venting stages; the pellet comes out grey and slightly odorous. Above that the pellet is only saleable as a dark-grade compound. Most plants blend printed film at 30–50% with clean film rather than running it alone.

What is the maximum contamination the line tolerates?

A single screw line tolerates about 2% non-melting contamination with 60–80 mesh. A two stage line handles 5–8% with 100 mesh because filtration pressure is decoupled. Above 8%, washing is cheaper than filtering: sand and paper belong in a wash tank, not in your screen pack.

Can I add filler or colour directly at the granulator?

On a single screw, only with a low-ratio dosing unit and 5–10% additive; dispersion will be poor. For 20% and above you need a twin screw with gravimetric dosing and a dispersion section. Colour masterbatch at 2–4% works acceptably on a single screw with a static mixer.

Power, space and installation

What power supply do the machines need?

Standard is 380 V / 50 Hz three-phase; we also build 415 V / 50 Hz, 440 V / 60 Hz and 220 V single-phase for the smallest mill. Motors are IE3, panels IP54, and every unit ships with a schematic matched to the ordered voltage.

How much floor space does a line need?

A strand line needs 8–12 m of length, a water ring line 5–7 m, a two stage line 15–18 m and a full washing plus pelletizing plant 32–58 m. Add 1.5 m of maintenance access on the drive side and 2 m at the control cabinet.

Do I need a special foundation?

A level, load-bearing concrete floor is enough for machines up to 120 mm screw; larger lines and two stage machines need isolated pads or vibration dampers. We send a foundation drawing with the order and check it against your site photos before shipping.

How much water does the line consume?

A closed-loop water ring uses 0.3–0.6 m³/h of make-up water. An underwater pelletizer uses 0.5 m³/h. A complete washing line consumes 0.8–1.2 m³ per ton of flake, and we size the water treatment to recirculate 90% of it.

Can you install and train our operators?

Yes: 7–10 days on site for a line, 3–5 days for a single machine, including commissioning, two days of operator training and a signed handover report. Buyer covers travel, accommodation and a local translator if needed.

Pellets and quality

What pellet size is standard?

3 mm is the default for injection and blow moulding; 2–2.5 mm for film and cable; 4 mm for large mouldings. Tolerance is ±0.2 mm on strand cutting and ±0.15 mm on underwater cutting. Below 2 mm, output drops and fines rise.

Why are my pellets sticking together?

Check in this order: cooling water above 45 °C, cutter speed too low, worn knives with more than 0.3 mm clearance, then bagging temperature above 45 °C. Nine out of ten cases are water temperature.

How do I reduce fines and dust?

Sharper knives, correct clearance, and a vibrating screen that removes what is already there. Underwater cutting produces the least dust; strand cutting with a worn bed knife produces the most. A 0.5% fines level is normal, 2% is a maintenance signal.

How is pellet quality inspected?

Per batch: sieve analysis for oversize, on-size and fines; bulk density; moisture by Karl Fischer or a halogen meter; and a 200 g visual check for black specks. For film customers, add a 20 µm blown-film trial every shift.

Can the pellet be food-contact certified?

The machine can be supplied with stainless contact parts, closed-loop water and documented process parameters, which is what certification bodies ask for. Actual food-contact approval also depends on feedstock traceability and, for PET, an SSP step; it is issued to the converter.

Price, payment and shipping

How much does a plastic granulator cost in 2026?

Indicative FOB Qingdao: a 100–150 kg/h compact mill from US$6,800; a 300 kg/h single screw line around US$18,000; a 600 kg/h two stage line around US$78,000; a 1,000 kg/h PET line from US$120,000. Configuration, voltage and cutter type move these figures by 10–25%.

What payment terms do you accept?

30% T/T deposit with the order, 70% before shipment against photos and video of the test run. L/C at sight is accepted for orders above US$50,000. We do not ask for full prepayment, and we do not ship against a promise.

What is the lead time?

15–20 days for a compact mill, 25–35 days for a standard line, 45–60 days for a custom line or a full washing plant, counted from deposit and drawing approval. Sea freight to Europe adds 30–40 days, to Southeast Asia 7–12 days.

Which countries do you ship to?

Forty-six markets so far, including Vietnam, Indonesia, Thailand, India, Poland, Turkey, Mexico, Brazil, Egypt, Nigeria and South Africa. We handle export documentation, CE files and fumigation-free crating; the buyer handles import clearance.

What does the warranty cover?

Eighteen months from commissioning or 24 months from shipment, whichever comes first, covering parts and labour for manufacturing defects. Wear parts — knives, screens, heater bands, seals — are excluded but stocked for three years.

Can I see the machine running before I pay the balance?

Yes — that is standard practice here. We send a video of the four-hour test run with your material, the PLC trend, the pellet sample photos and the test report, then you pay the balance. If the result misses the agreed output by more than 5%, the deposit is refundable.

Next step

Question not answered above?

Send the polymer, contamination level and target output. You get a model recommendation, power estimate and price range within one working day.

العربيةAR