The screen changer is the filter in the middle of the line, and it is the single component that decides whether the pellets leaving your extruder are the pellets the customer is willing to pay for. It sits after the melt has been homogenised and before it is cut, and its job is to hold back the last solids that the screw never fully dispersed.
What it does not do is sanitise the material. A screen stops particles; it does not stop oil, it does not stop moisture, and it does not stop a polymer that has already degraded. A 60–80 mesh screen on a single screw will pass something above two percent non-melting contamination more or less indefinitely, because the screen was never given that job.
What the filter is and is not responsible for
- Filtration removes solids, not chemistry. Oil and moisture need washing and drying.
- A single screw tolerates about 2% non-melting contamination at 60–80 mesh; a two-stage set-up handles 5–8% at 100 mesh.
- Above 8% contamination, washing is cheaper than filtering — the screen will simply block faster than you can change it.
- Pressure rise, not the clock, decides when to change a screen.

The job the melt filter does in the middle of the line
A screen changer sits between the extruder and the die. Its job is to intercept anything solid that did not melt — carbonised polymer, unmelted filler, degraded gel, metal fragments — before they reach the die and become a defect in a pellet that a customer will reject.
That sounds like a minor function. It is not. Everything downstream of the filter assumes the melt is clean: the pressure gauge reading means something, the pellet size is uniform, the die face does not foul. A blocked filter does not just pass dirt through; it changes the pressure profile of the whole extrusion, and a machine run at the wrong pressure produces inconsistent pellets even from clean material.
This is why the site treats the screen changer as a named product with its own entry in the auxiliary equipment index, rather than as a small part of the extruder. In practice it is one of the two components — together with the die head — that decide whether a line can run a contaminated feedstock at all.
What actually gets filtered, and what gets through

Contamination in recycled feedstock is not one thing. It is a mixture, and different mechanisms catch different parts of it.
Non-melting solids — sand, glass, metal, paper, filler — are large enough to be caught by any reasonable screen and are the primary target. This is the easy half of the problem.
Carbonised polymer — material that sat too long in a hot zone and degraded into black particles — is harder. It is the same polymer, so it melts into the melt, but it does so late, at a temperature high enough to char the material around it. These are the black specks that appear in an otherwise clean pellet.
Oxidised gel behaves similarly and is what turns a batch yellow. Neither is caught by a screen that is sized for filler; both need the residence time to be controlled as well as the filter to be correct.
Dissolved degradation products — the volatiles and oxidised species that make PET lose intrinsic viscosity — pass through any filter. No screen fixes a polymer that has degraded in the barrel. That is a venting and residence-time problem, and it is why the FAQ answer on contamination thresholds stops at filtering rather than pretending a finer mesh solves it.
How mesh and pressure interact
Filter area is the number to think in, not mesh count. The working rule from the industry selection guides is: filter area in cm² = melt flow in kg/h ÷ (filter factor 0.2–0.6 × material density in g/cm³). A 500 kg/h HDPE melt therefore needs roughly 250 cm² of screen area.
Once you have the area, the mesh sets what the filter catches and the pressure tells you how it is coping. Our published mesh choices by duty are 60–80 mesh for a single screw handling about 2% non-melting contamination, and 60–100 mesh on a two-stage line for 5–8%. Above 8%, washing is cheaper than filtering — sand and paper belong in a wash tank, not in your screen pack.
A finer mesh is not a free upgrade. It raises pressure drop, shortens the time between screen changes, and increases the wear rate on the screen changer itself. The measured pressure rise across the filter is the only honest indicator of when it needs changing, and on a machine with a differential pressure gauge you do not need a schedule at all.
Where the filter sits in the machine range
The screen changer is one of thirteen entries on our auxiliary equipment index, sitting beside the die head, the melt filter, the pellet cutter, the silo, the mixing tank and the plastic dryer. Those are the parts that turn an extruder into a production line, and they are specified together or not at all.
In our own machine range the filtration duty is part of what defines the platform. The single screw granulator handles clean regrind with a hydraulic screen changer; the two-stage granulating line adds a second filtration stage at 60–100 mesh specifically so that filtration pressure is decoupled from extrusion pressure — which is what lets it hold die pressure stable through a shift on high-contamination waste.
Filtration duty by contamination level
Filtration duty follows from how contaminated the feed is, and the table starts from the contamination level rather than from the mesh.
| Contamination | Machine | Screen mesh | Note |
|---|---|---|---|
| Below 2% | Single screw granulator | 60–80 mesh | Single filtration stage is sufficient |
| 2–8% | Two-stage granulating line | 60–100 mesh | Second stage decouples filtration from die pressure |
| Above 8% | Wash first, then pelletize | Not a filtering problem | Sand and paper belong in a wash tank |
Questions buyers ask about this machine
Q1: What does a screen changer remove from the melt?
Solid non-melted particles: sand, glass, metal, paper, unmelted filler and carbonised polymer fragments. It does not remove dissolved degradation products, so it cannot rescue material that has already aged in the barrel — that is a venting and residence-time problem.
Q2: How often should the screen be changed?
On our lines, a screen change takes about 20 minutes and is scheduled every 3–4 hours on a continuous-duty machine, with an 8-hourly blade check alongside it. On heavily contaminated feed the interval shortens. If the machine has a differential pressure gauge, change on the reading rather than on the clock.
Q3: Does a finer mesh always give better pellets?
No. Finer mesh catches more, but it also raises the pressure drop, shortens the interval between screen changes and wears the screen changer faster. The right mesh is the one that holds die pressure stable for a full shift without fouling, not the finest one available.
Q4: What is the difference between a screen changer and a melt filter?
A screen changer is a serviceable pressure vessel that lets you swap a filter without opening the barrel — it filters continuously while one position is on line. A melt filter is typically the filtration element itself, in either manual or hydraulic form. The two names are often used for overlapping things, which is why we specify filter area, mesh and changeover method rather than the product name.
Related pages on this site: the 12-platform comparison and pellets and feedstock terms.
If you are working through the same machine family, these are the other Manual, Hydraulic or Continuous Screen Changer: Which?, Screen Changer Filter Area: Calculation and Pressure, Screen Change and Maintenance Routine for Plastic Extruders and Screen Changer Cost: What It Costs and What It Saves.
About the author
Zhou Gong (周工) is the recycling machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong — a plant of 18,000 m² with 30-plus staff, 12 platforms and 820-plus installations across 46 export markets. When I look at a contaminated-pellet complaint, the first thing I ask for is a sieve analysis of the pellets, because without it the conversation is guesswork. Where a figure is quoted here it has been measured or published with a date attached; nothing in this article is an estimate.
The quickest way to a real answer is to send the feed form, the contamination level and the throughput you need. A model and a price range come back within one working day, the trial on 10–20 kg of your material is free, and a result that misses the agreed output by more than 5% leaves the deposit refundable.