Published 2026 listings for underwater pelletizers run from about 30 kg/h on a screw below 65 mm to 10,000 kg/h at the top of the range. Small systems below 65 mm quoted 100–200 kg/h at CNY 20,000–50,000, mid-range 90–120 mm machines quoted 300–500 kg/h at CNY 80,000–180,000, and large units above 150 mm quoted 800–1,500 kg/h above CNY 250,000. Complete export systems are quoted at US$80,000–200,000 per set.
Plan on 60–80% of the nameplate, and the reason is not caution. A nameplate rate assumes washed, dried flake at specification, a steady feed and a cutter running at its rated speed. Everything that makes a real plant different — moisture, contamination, the material arriving in mixed bales — takes the top off that number.
What the published numbers do not tell you
- Published capacity spans 30–10,000 kg/h; a 1,000 kg/h rigid PP/PE line is quoted at US$60,000–300,000 per set.
- Plan 60–80% of nameplate. Real plants reach the catalogue number only with washed, dried, in-specification flake.
- Make-up water is about 0.5 m³/h; the plant needs a connection and a treatment loop for it.
- The space people forget is behind the machine: cutter access, screen changes and pellet conveyance.

The published capacity range, and what it means
Underwater pelletizing equipment on the market spans an unusually wide range: published 2026 figures run from 30 kg/h to 10,000 kg/h across the supplier range. That spread is real and it reflects genuine differences in screw diameter, drive power and cutter design.
Our own TL-UW platform covers 300–2,000 kg/h and starts at US$62,000 ex works, sitting above the strand pelletizing line at US$16,800 and the water ring at US$18,500. The TL-PET line above it covers 500–2,000 kg/h at US$120,000 and includes the crystallisation and dehumidified drying that food-contact PET requires.
The published Chinese price bands are worth knowing for orientation: small machines below a 65 mm screw at 100–200 kg/h around CNY 20,000–50,000; mid-range 90–120 mm screw at 300–500 kg/h around CNY 80,000–180,000; large machines above 150 mm screw at 800–1,500 kg/h above CNY 250,000, with export systems quoted at US$80,000–200,000 per set and a 1,000 kg/h rigid PP/PE line listed at US$60,000–300,000.
Plan on 60–80% of the nameplate

This is the number that catches people out, and it applies to the whole industry rather than to one machine.
Catalogue capacity assumes 85% bulk density, 3% moisture and moderate contamination. Wet film at 60 kg/m³, flake with 8% water, or a very fine screen can each cut real output by 20–40%. A washing line quoted at 2,000 kg/h on paper will typically run at 1,200–1,600 kg/h on the floor.
We quote finished, bagged pellets averaged over four hours, which runs 3–6% below extruder throughput because of fines, purges and start-up. When a supplier quotes screw throughput instead, the number is larger and the two are not comparable.
So: if you need 800 kg/h of saleable output, plan for a machine nominally rated at 1,000–1,300 kg/h, and confirm the figure in the contract as finished output over a four-hour average.
The floor space question, and the space people forget
Against a strand line, an underwater system needs about 40% less floor space, which is the headline advantage and the reason it is specified where floor space is tight.
Our published footprint figures are 8–12 m for a strand line, 5–7 m for a water ring line, 15–18 m for a two-stage line, and 32–58 m for a complete washing plus pelletizing plant. Underwater sits with the water ring end of that range.
Three things are routinely missing from a layout drawn on paper. The first is access: 1.5 m of maintenance access on the drive side and 2 m at the control cabinet. The second is the water loop — the tank, the filtration and the place the water goes, which is not optional on an underwater system and often lands outside the machine footprint on the drawing. The third is the pellet cooling and conveying route from the cutter chamber to the drying and bagging station.
And the foundation: a level, load-bearing concrete floor is enough up to a 120 mm screw, but larger lines and two-stage machines need isolated pads or vibration dampers. We send a foundation drawing with the order and check it against your site photographs before shipping.
Matching the pelletizer to the rest of the plant
An underwater pelletizer rarely stands alone. It sits between a feed preparation stage and a drying and bagging stage, and each of those has a throughput expectation that should match.
For PET, the upstream requirement is crystallisation and dehumidified drying to below 50 ppm. For polyolefins, it is a stable, dense feed — and where the feed is film, that means densification upstream, because an underwater cutter does not solve a feeding problem.
Downstream, the pelletizer needs a dryer and a bagging or silo destination, plus a vibrating screen to remove fines. Our auxiliary equipment index carries the silo, the storage hopper, the mixing tank and the auto loader that finish that chain.
The planning mistake worth naming is buying the pelletizer first and then designing around it. The output figure of the plant is set by the weakest stage, and the pelletizer is rarely the weakest — it is usually the feed preparation in front of it.
Underwater pelletizer capacity and price bands, 2026 published listings
Published 2026 listings, read against the throughput a plant should actually plan for.
| Class | Screw | Capacity | Price band |
|---|---|---|---|
| Small | Below 65 mm | 100–200 kg/h | CNY 20,000–50,000 |
| Mid | 90–120 mm | 300–500 kg/h | CNY 80,000–180,000 |
| Large | Above 150 mm | 800–1,500 kg/h | Above CNY 250,000 |
| Export systems | Varies | 30–10,000 kg/h | US$80,000–200,000 per set |
Frequently asked questions
Q1: How much of the rated capacity should I plan on?
60–80%. Catalogue figures assume 85% bulk density, 3% moisture and moderate contamination; wet film, wet flake or a fine screen can each cut real output by 20–40%. Size for your required saleable output, not for the nameplate.
Q2: How much floor space does an underwater pelletizer need?
Roughly the same as a water ring line, at 5–7 m for the machine itself, against 8–12 m for a strand line. Add 1.5 m of access on the drive side and 2 m at the control cabinet, and allow space for the circulating water system, which is part of the installation and often drawn separately.
Q3: Does an underwater pelletizer need a special foundation?
A level, load-bearing concrete floor is sufficient up to a 120 mm screw. Larger lines and two-stage machines need isolated pads or vibration dampers. We send a foundation drawing with the order and check it against your site photographs before the machine ships.
Q4: Can I run an underwater pelletizer on PP and PE in the same week?
Yes. PP runs 10–15 °C hotter than LDPE, so store both recipes in the PLC and the change is a five-minute temperature ramp plus a purge. What you cannot mix is colour: a dark-to-light change takes 40–60 minutes of cleaning.
The pages that come up most often alongside this one: plastic granules production line, the 12-platform comparison and turnkey pelletizing solutions.
The companion write-ups for this machine family are: Underwater Pelletizer vs Strand and Water Ring Cutting, Underwater Pelletizer: Pellet Quality and Oxidation Control, Underwater Pelletizer Commissioning and Acceptance and When an Underwater Pelletizer Is the Wrong Choice.
About the author
Zhou Gong (周工) is a recycling machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong, where 30-plus staff work across 18,000 m² and 12 machine platforms covering 100 to 3,000 kg/h. The number I never accept from a supplier is the nameplate output without a material and a moisture figure attached to it — that number means nothing. Every figure used here has been measured on a machine or taken from a dated published source, not from a brochure.
Send the material form, the contamination level and your target output to our engineering team and you get a model and a price range within one working day. A test run on 10–20 kg of your own material is free, and if the measured output misses the agreed figure by more than 5%, the deposit is refundable.