Underwater pelletizing cuts the melt inside a water-filled chamber, so the strand is quenched the instant it leaves the die instead of cooling in air. The result is a spherical pellet with no visible cut face, typically 1.2–3 mm, cut to ±0.15 mm. A strand line cools in air and cuts a strand into cubes, typically 2–4 mm, to ±0.2 mm, and it leaves visible die lines on every cube face.
The water is not simply cooling the melt. It carries the heat away fast enough to keep the polymer below its oxidation window, which is why underwater cutting holds colour and intrinsic viscosity on heat-sensitive grades where strand cutting does not. It also means a circulating water system, a make-up water figure of about 0.5 m³/h, and a cutter that is a wear item rather than a fixed blade.
Three cutting methods, three different products
- Underwater gives spherical 1.2–3 mm pellets to ±0.15 mm and the best colour retention.
- Water ring gives die-face cut pellets with 40% less floor space than a strand line.
- Strand gives 2–4 mm cubes, the easiest to inspect visually, at the lowest capital cost.
- Underwater needs circulating water at about 0.5 m³/h make-up, against 0.3–0.6 m³/h for a closed-loop water ring.

Three ways to cut a melt, and what each produces
Once the polymer is molten, the pelletizing question is how to cool it and cut it. There are three established answers, and they produce materially different pellets.
Strand cutting extrudes strands into air or a shallow cooling trough and cuts them with a rotating bed knife. It produces cubic pellets of 2–4 mm, it is the simplest visual quality check there is, and it produces the most fines — a worn bed knife produces dust, and 0.5% fines is normal while 2% is a maintenance signal.
Water ring cutting extrudes strands into a ring of water where they are cut at the die face. It needs about 40% less floor space than a strand line, and it produces round pellets rather than cubes.
Underwater cutting pushes the melt directly into a water-filled cutter chamber where a rotating cutter cuts it as it arrives, and the pellets are conveyed out in the water. It produces spherical pellets of 1.2–3 mm, it produces the least dust of the three, and submerged cooling largely prevents the oxidation that turns material yellow.
What the water actually does to the pellet

The mechanism is worth understanding because it explains most of the practical differences.
A polymer melt that meets air is exposed to oxygen at a temperature where oxidation is fast. The surface degrades, gels form, and the pellet discolours. This is the reason a strand line running PP has to be purged carefully and why dark-to-light colour changes take 40–60 minutes of cleaning.
In an underwater system the melt never sees air. It is extruded straight into water, cooled below the oxidation threshold within seconds, and cut while still submerged. The result is a sphere with an oxidised skin of essentially zero and a clean interior, and it is why underwater pellets are the natural choice for food-contact and medical-grade material.
The water also does the transport. Pneumatic conveying of hot pellets is avoided, which removes a whole class of handling dust problem from the plant.
Where each method wins and where it does not
Underwater is not the best answer everywhere, and choosing it because it sounds more advanced is a common and expensive mistake.
Underwater suits PET, PA and masterbatch — which is why our TL-UW platform is specified for exactly that: PET, PA and masterbatch, spherical 1.2–3 mm, 300–2,000 kg/h. The polymers that degrade easily and the applications that cannot tolerate a yellow pellet are where it earns its price.
Strand suits cubic pellets for cable and film applications, where the customer specifies a cube and a 3D visual check is part of the incoming inspection. It also suits smaller tonnages, because the capital is lower.
Water ring is the compromise for producers who want round pellets without the full underwater package, and it is the right answer for polyolefins where appearance is not critical and floor space is.
One more practical difference: an underwater system circulates water, so it needs a water loop, a filtration stage and somewhere for the circulated water to go. Our published figure is 0.5 m³/h of make-up water, against 0.3–0.6 m³/h for a closed-loop water ring. In a plant with water treatment already in place, that difference is nothing. In a plant without it, it is a real cost.
The pellet you end up with
The specification of the pellet is where the choice becomes visible in your customer contract.
Our published sizes are 3 mm as the default for injection and blow moulding, 2–2.5 mm for film and cable, and 4 mm for large mouldings, with a tolerance of ±0.2 mm on strand cutting and ±0.15 mm on underwater cutting. Below 2 mm, output drops and fines rise.
Bulk density and shape follow from the method as well. A cube stacks with voids; a sphere packs tighter and flows better. That matters for the customer’s dosing equipment and for how the pellet handles in their hopper, and it is worth stating in the specification rather than leaving to be discovered.
Cutting methods compared
The three cutting methods below produce measurably different pellets from the same melt, and the differences are worth more than they look.
| Method | Pellet shape | Size | Fines | Best for |
|---|---|---|---|---|
| Strand | Cubic | 2–4 mm | Highest — 0.5% normal, 2% is a signal | Cable, film, smaller tonnages |
| Water ring | Round | 3–4 mm | Low | Polyolefins, limited floor space |
| Underwater | Spherical | 1.2–3 mm | Lowest | PET, PA, masterbatch, food-contact |
Common questions, with short answers
Q1: What is the difference between a water ring pelletizer and an underwater pelletizer?
In a water ring the strands are cooled in water and cut later by a separate cutter head. In an underwater system the melt is cut inside the water as it arrives, which means the melt never meets air and the pellet is spherical. The underwater route gives a cleaner, rounder pellet and less dust; the water ring is simpler and cheaper.
Q2: Is an underwater pelletizer suitable for food-contact PET?
It is the reason food-contact PET is normally pelletized underwater. The melt never contacts air, so oxidation is minimised, and the spherical pellet is what injection moulders expect. For actual food-contact approval you also need stainless contact parts, closed-loop water and documented process parameters — and, for PET, an SSP step. The approval itself is issued to the converter, not to the machine.
Q3: Which polymers should not run underwater?
Polyolefins that are not appearance-critical do not need it, and the capital is better spent elsewhere. PVC needs a dedicated configuration with corrosion-resistant screw and barrel and no long residence at temperature, and it is the one material where heat exposure punishes misconfiguration fastest.
Q4: Does underwater pelletizing need a lot of water?
Our published figure is 0.5 m³/h of make-up water for an underwater pelletizer, which is a circulating loop with filtration rather than continuous throughput. A closed-loop water ring needs 0.3–0.6 m³/h. The difference is modest, but a plant without existing water treatment will feel it in the installation budget.
Related pages on this site: granulator types and the 12-platform comparison.
If you are working through the same machine family, these are the other Underwater Pelletizer: Pellet Quality and Oxidation Control, Underwater Pelletizer Sizing: Throughput and Floor Space, Underwater Pelletizer Commissioning and Acceptance and When an Underwater Pelletizer Is the Wrong Choice.
About the author
Zhou Gong (周工) builds recycling lines at TENGLONG Plastic Machinery, a factory in Linyi, Shandong, with 18,000 m² of floor area, 30-plus staff and 820-plus lines delivered to 46 export markets. The test I run on any pellet sample is a warm-water soak: colour that shifts in warm water was oxidised in the melt, not in storage. The numbers in this article come from test runs and from dated published sources, not from a sales sheet.
If you want a recommendation rather than a catalogue, send the material form, the contamination level and the target output. We return a model and a price range within one working day, and the test run on 10–20 kg of your own material is free before the balance is paid.