CE marked · ISO 9001:2015 · 18-month warranty

· products · By

Plastic Pellet Mill Startup, Step by Step

A timed startup sequence for a plastic pellet mill: cold checks, heat soak, no-load current, first feed, knife setting and the values to log.

TENGLONG TL-PM plastic pellet mill — product photograph from the TL-PM range

Summary: A plastic pellet mill goes from cold to steady pellets in about two and a half hours, and the order of the steps matters more than the speed. This is that sequence written as a sheet you can follow: sixty minutes of cold checks, forty minutes of heat soak on the barrel and die plate, a dry run where no-load current should sit at 30 to 40% of full load, then first material fed in current steps rather than all at once. Knives are set on running material, not cold, and the ring water and dewatering stage are trimmed last. Every step gives the instrument to read, the normal band and the condition that tells you to back off, so a first-time operator can run it without a technician on site.

TENGLONG TL-PM plastic pellet mill — product photograph from the TL-PM range
TENGLONG TL-PM plastic pellet mill: one of the configurations in the published TL-PM range.

T-minus 60 minutes: the cold checks that save the hot hour

Everything in this hour is done with the TL-PM plastic pellet mill cold, because that is the only time it is safe to put a hand near the die. Work down the list and do not shorten it; a fault found here costs ten minutes, and the same fault found with the barrel at 220 °C costs a shift.

  • Electrical — rotation direction confirmed, terminals torqued, earth continuity checked, emergency stop tested under power.
  • Die plate — all holes clear, face flat, clamp bolts torqued in a cross pattern.
  • Knives — clearance set and edge inspected with a loupe; two spare sets within reach.
  • Water circuit — ring filled, strainer clean, pump turns freely by hand.
  • Guards and ducting — cutter guard, coupling guard and blower duct secure.
  • Feed — flake dry, size consistent, hopper empty of last week’s material.

The last item is the one people skip. Old material in the hopper has picked up moisture from the air, and the first twenty kilograms of a shift are then wet feed pushed through a cold die: the two conditions that block holes. Start with a clean hopper and a dry bag.

T+0 to T+40: heat soak, and why the die plate leads

Bring the zones up to the working band, 180 to 240 °C across four zones depending on polymer, and let them soak. The barrel is not the reason. The reason is the 200 mm die plate: it grows as it heats, and a plate clamped cold carries a different bolt load at 220 °C. Soaking lets the plate reach a stable dimension before polymer is pushed through it, which is what keeps the head from leaking on the first shift of the week.

What to watch during the ramp

Each zone should be within 5 °C of setpoint by T+25. A zone that lags by 20 °C at T+30 is a failed heater band or a thermocouple out of its pocket; stop and fix it, because feeding into a cold zone is how a screw gets overloaded. Watch the die plate temperature separately if a sensor is fitted there — it trails the barrel zones by ten minutes or more, and it is the number that decides when feeding is safe. the pellets and feedstock glossary has the zone and setpoint vocabulary if the panel labels differ from this sheet.

The most common startup error is feeding at 150 °C because the barrel feels hot to the hand. At that temperature the polymer is soft but not fluid, the screw has to force it through cold capillaries, and current climbs into the overload band within a minute or two. Wait for the band, then wait five more minutes.

T+40 to T+55: dry run, no-load current and the sound of the machine

With no feed, run the screw at low speed for five minutes and read the current. No-load current sits at 30 to 40% of full load: about 30 to 38 A on a 55 kW unit whose full load current is roughly 95 A at 380 V. A figure well above that with an empty barrel means something is tight — a cold zone, a misaligned coupling, or polymer left in the die from the last run.

Listen at the same time. At one metre the normal sound level is 78 to 82 dB(A), dominated by the cutter and the blower, and it is steady. A new metallic knock, a rising whine from the gearbox or a rhythmic scrape is not a normal sound and is cheaper to investigate now than after the first tonne. Check the ring water is circulating and that the strainer is not pulling air, and confirm the cutter turns freely by hand with the drive isolated.

The one test worth doing every week

Record the no-load current in the log. It is the cheapest condition indicator on the machine: a bearing or alignment problem shows up as a slow drift in that number weeks before it shows up as a breakdown, and a drift of 10% against last month’s figure is worth a look at the coupling and the die.

T+55 to T+85: first material, in steps rather than all at once

Start the feed at the lowest setting the drive allows and watch current, not output. Step up in increments that hold for five minutes each, and stop stepping when current reaches 85 to 90% of full load. That is the working point for the rest of the shift: the machine has headroom for a wet patch in the feed without tripping, and the die is running at the pressure it was designed for.

Inspect the pellet at every step. A good cut on a 2.5 to 4 mm die gives uniform cylinders with square ends, a small fines fraction, and no steam at the die face. Tails at low rate mean the knives need setting, which is the next step. Tails that appear only as the rate rises mean the cutter has reached its limit at that clearance, and the answer is clearance rather than more speed.

What to do when it trips here

If the overload trips during this ramp, do not reset and try again at the same setting. Drop two steps, hold for ten minutes, and check that all four zones are still at setpoint; a zone that fell 15 °C under load is the cause, not the feed rate. crushers and shredders matters at this point too, because a sudden change in flake size from the grinder behaves exactly like a feed rate that is too high.

T+85 to T+105: set the knives on running material

Setting clearance cold is guesswork, because the cutter and the die plate are at different temperatures and grow differently. Set it hot, with pellets running, and adjust in steps of a few hundredths of a millimetre. Between steps, run two minutes and look at the sample: clean square ends mean the clearance is right, tails mean it is still too large, and flat or smeared pellets with a rise in fines mean it has gone too tight.

Do not adjust the knives and the temperature at the same time. Both change the cut, and if you move both you will not know which one fixed it — or which one caused the next problem. This is the single most useful discipline on a small machine, where the same person is watching the panel and the sample tray.

When the cut will not come clean

If clearance is correct and the tail persists, check the die face for dishing with a straight edge. A dished plate cannot be cut cleanly at any clearance, and no amount of knife adjustment will fix it. That is a refacing job, and it is worth catching on the first shift rather than after a week of off-spec pellets.

T+105 to T+150: water, dewatering and the first log

Trim the ring water last, because it affects the pellet rather than the cut. The rule of thumb is to keep it cool enough that a pellet is set before the next knife arrives; in practice that means below about 45 °C at the die face on most polyolefins. Warmer water gives softer pellets that deform in the takeaway bin, and colder water costs refrigeration for no gain in quality.

Then check the dewatering end: the slotted screen and blower should take pellets to about 0.5% surface moisture. Squeeze a handful in a clear bag — visible droplets on the film after a minute mean the screen is blinded or the blower duct is loose. auxiliary equipment covers the blower and conveying options if the takeaway run is longer than a few metres.

What goes in the log, and what happens at shutdown

Write eight numbers at T+150: four zone temperatures, screw speed, no-load current from the dry run, feed rate at 85% of full load current, and ring water temperature. That page is the baseline for every fault in the 33 answered questions and for next month’s comparison.

Shutdown is part of startup, because a bad stop is tomorrow’s blocked die. Stop the feed first, let the barrel run empty for two minutes, then purge or run the die empty, stop the screw, stop the heaters, and wash the dewatering screen while it is still warm. Ten minutes here removes the most common cause of a bad start tomorrow.

The startup sequence with its clock times, the instrument to read at each step, the normal band and the condition that means back off.
Clock Step Read Normal band Back off if
T-60 Cold checks, die clear, guards on E-stop, earth, feeler gauge All checks pass Any check fails
T+0 Heat up, four zones Zone temperatures 180-240 °C A zone lags 20 °C at T+30
T+25 Soak the die plate Die plate temperature Within 5 °C of setpoint Plate trails barrel by more than 15 °C
T+40 Dry run, no feed Main motor current 30-40% of full load, 30-38 A on 55 kW Current above 45% with an empty barrel
T+40 Listen and check water Sound, flow, strainer 78-82 dB(A) steady, water circulating Metallic knock or air in the pump
T+55 First feed in steps Current and pellet sample 85-90% of full load, square pellet ends Trip, or tails that grow with rate
T+85 Set knives hot Sample under a loupe Clean cut, low fines Flat or smeared pellets
T+105 Trim water, check dewatering Water temperature, bag test Below about 45 °C, 0.5% surface moisture Droplets on the bag film

Frequently asked questions

Q1: How long does it take to start a plastic pellet mill from cold?

Plan about two and a half hours to first steady pellets: sixty minutes of cold checks, forty minutes of heat soak to 180-240 °C, fifteen minutes of dry run, thirty minutes of feeding in steps and twenty minutes of knife and water trimming. The soak cannot be shortened safely, because a cold die plate leaks and blocks.

Q2: What current should the main motor draw with no material in the barrel?

No-load current should sit at 30 to 40% of full load, which is about 30 to 38 A on a 55 kW unit rated near 95 A at 380 V. A higher figure with an empty barrel points to a cold zone, a tight coupling or old polymer left in the die. Record it weekly: a slow drift is the earliest sign of a bearing or alignment problem.

Q3: How do I set the knife clearance on a plastic pellet mill?

Set it hot, with pellets running, because the cutter and die plate grow differently as they warm. Adjust in steps of a few hundredths of a millimetre and check the sample after each step: square ends mean correct clearance, tails mean too much, flat or smeared pellets with rising fines mean too little. Never adjust clearance and temperature at the same time.

Q4: Why must the die plate soak before feeding starts?

The 200 mm die plate grows as it heats, so a plate clamped cold carries a different bolt load at working temperature. Soaking lets it reach a stable dimension before polymer is forced through the capillaries, which prevents head leaks and gives an even cut from the first pellet. Watch the plate temperature rather than the barrel zones.

Q5: What should I record during the first hour of running?

Eight values at T+150: the four zone temperatures, screw speed, no-load current from the dry run, the feed rate that holds 85% of full load current, and ring water temperature. That page becomes the baseline for fault finding and for month-on-month comparison, and it is the only record that tells you whether the machine or the material has changed.

Engineer’s note

The step customers skip is the soak, and it is the one I would keep if I could keep only one. A die plate at 180 °C is a different size from the same plate at 20 °C, and every leak we are asked about starts with feeding before the plate has settled. Our own test runs hold the machine at temperature before the first kilogram, and the PLC record shows it.

Engineering note: the numbers on this page are our own published reference ranges for the machine family, not a specification guarantee for any individual unit. Final output, specific energy and pellet quality are set by the incoming material, its moisture and contamination level, and the screen pack fitted. We write the confirmed figures onto the quotation after a factory test run on your own material.

Who wrote this

Zhou Gong (周工) is a senior plastic machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong. The factory was registered as Linyi Hedong District Tenglong Plastic Machinery Factory on 7 June 2016 and grew out of a screw and barrel workshop, so his work is rooted in the parts that decide whether a granulator holds output: screw geometry, nitriding case depth, barrel alignment and melt filtration. He prepares the technical specification for customer quotations, reviews the four-hour factory test data before shipment, and runs commissioning support on site. Screws are nitrided in-house to a 0.5–0.7 mm case at HV 900–1000 and straightened to 0.03 mm runout over the full length; barrel, screw, gearbox and frame are aligned to 0.05 mm before the test run.

Figures quoted here are engineering reference ranges published on our own product pages, not guaranteed values for any specific machine. Real output, specific energy and pellet quality depend on the incoming material, its moisture and contamination level, and the screen pack fitted. Final values are written after a factory test run on the customer’s own material, and the PLC-logged test report ships with the machine. For a quotation that reflects your material, send the feed form, contamination level and target output and a configuration comes back within one working day.

Ask for the startup sheet that ships with the machine, written for your polymer and your die. Request the commissioning checklist and it comes back with the quotation.

Related reading

العربيةAR