CE marked · ISO 9001:2015 · 18-month warranty

· products · By

PET Pelletizing Line and rPET Intrinsic Viscosity

How the TL-PET line protects rPET intrinsic viscosity, why moisture destroys it at 0.01 dl/g per 100 ppm, and where drying and venting come in.

Intrinsic viscosity is the number that decides what rPET pellets are worth, and moisture is the only thing on the line that moves it: PET loses 0.01 dl/g of IV for every 100 ppm of water in the melt. The TL-PET line holds the total loss below 0.03 dl/g at 500–2,000 kg/h.

Bottle-grade rPET is specified at 0.80–0.84 dl/g and fibre-grade at 0.70–0.78 dl/g, so the loss has to stay inside a band you cannot argue with later. The line protects that band with crystallization, dehumidified drying to about 50 ppm and multi-stage venting, in that order.

Moisture is the whole mechanism

  • Bottle-grade rPET runs at 0.80–0.84 dl/g, fibre-grade at 0.70–0.78 dl/g.
  • PET loses 0.01 dl/g of IV for every 100 ppm of moisture in the melt.
  • Flake below 0.5% moisture and pH below 8.0, or the melt foams and yellows.
  • The published budget is IV loss below 0.03 dl/g at 500–2,000 kg/h.
3D product render of a TENGLONG plastic pelletizing machine on a white background, shown here as a visual reference for intrinsic viscosity control.
3D product render of a TENGLONG plastic pelletizing machine on a white background, shown here as a visual reference for intrinsic viscosity control.. Used here as a visual reference for how a PET pelletizing line holds intrinsic viscosity. Rendering, not a photograph of a customer plant.

Intrinsic Viscosity Is the Number That Decides the Price

Intrinsic viscosity is the figure that decides whether food-grade rPET is worth food-grade money and whether a buyer will take it. Bottle-grade rPET is specified at 0.80–0.84 dl/g and fibre-grade at 0.70–0.78 dl/g, and those bands are narrow enough that a line which shifts the melt by half a band has produced a different product. The TL-PET line holds IV loss below 0.03 dl/g at 500–2,000 kg/h, which is a loss figure rather than an absolute figure, and the distinction matters when the incoming flake is already degraded.

Because IV is measured against the incoming material, the same machine gives different results on different streams. A bottle stream already sitting at the low end of the bottle-grade band cannot leave the line at the top of it. The line controls the loss; sorting and washing control the starting point. Any supplier quoting an absolute IV number for your material without having seen that material is quoting a number they read somewhere.

The commercial link is direct. In April 2026 rPET sold at US$1,130/t for fibre-grade clear pellets with IV 0.72 and US$1,300/t for food-grade pellets with IV 0.88, while non-food-grade clear or mixed-colour rPET was reported at US$800–1,200/t and super-clean food-grade rPET at US$1,500–2,500/t. Intrinsic viscosity is the variable that separates those price bands, and the plastic pellets glossary defines the term alongside the other specifications that travel with it.

Moisture Is the Only Thing That Moves the Number

Rendered factory scene with TENGLONG plastic pelletizing machine and operators on the plant floor, shown here as context for a machine installation in a plant hall at a PET pelletizing line.
Rendered factory scene with TENGLONG plastic pelletizing machine and operators on the plant floor, shown here as context for a machine installation in a plant hall at a PET pelletizing line.. Shown here as production context. Rendering, not a photograph of a customer plant.

PET is hygroscopic and the water in wet flake triggers thermal hydrolysis in the melt, which breaks the polymer chain and permanently drops the intrinsic viscosity, producing brittle low-value pellets. The published rate is simple: PET loses 0.01 dl/g of IV per 100 ppm of moisture. That is a steep exchange rate, and it explains the whole architecture of the line. There is no adjustment on the extruder that recovers IV once the chain has been broken.

Hydrolysis does not run backwards in a barrel. Once the chain is shortened under heat and moisture, the shortened chain is what gets pelletized, and the pellet carries that shortened chain into the customer’s injection machine. This is why water has to be removed before the melt forms rather than after, and why a line that can only filter moisture out of the melt is solving the wrong problem at the wrong point in the chain.

The practical consequence for a buyer is that the moisture specification has to come from the dryer and the vent, not from the extruder settings. It also means the tolerance for a wet hopper is small. A line standing unloaded overnight with the hopper open is a line that will make off-spec pellets the next morning, and the fault will be blamed on the screw because the screw is the part everybody watches.

Crystallization and the Drying Window

Crystallization, dehumidified drying to about 50 ppm and vacuum venting are all required here, because moisture hydrolyses PET and destroys intrinsic viscosity. The crystallization step is the one that is routinely underestimated in quotations. Crystallizing and underwater pelletizing capability was added in 2022 for food-grade rPET, and that combination is what allows the line to hold a moisture target at production speed rather than only at laboratory speed.

Drying has to be specified as a target, not as a machine. PET to below 50 ppm after crystallization is the published figure for this material, and flake moisture below 0.5% is the condition for stable extrusion. Those are two different statements about two different points in the process, and a quote that gives you a dryer size without a moisture target has not answered the question. Ask for the figure the dryer holds at rated throughput, not the figure it reaches on a trial.

Chemistry also enters through the wash. A flake pH below 8.0 keeps residual caustic from foaming the melt and yellowing the pellet. Caustic comes from the hot wash upstream, which is why the drying and washing specifications are written together in every serious food-grade document. The hydrolysis argument and the caustic argument are separate failures with one common cause, and that cause is a wash line that has drifted away from its own settings.

Vacuum Venting and What It Cannot Do

The multi-stage vacuum degassing system on this line pulls volatiles out of the melt at -0.08 to -0.1 MPa, and fine PET dust blocks those vacuum ports if it is not removed after washing. On a line like this the vent is where three separate specifications meet: moisture that survived the dryer, volatiles from the polymer, and the dust the wash line was supposed to have taken out. The system handles the first two. It cannot handle the third.

That is worth saying plainly to anyone watching the vent pressure gauge. A slowly rising vacuum level in the first weeks of production is not the machine settling in. It is dust accumulating in the ports, and the cure is upstream in the filtration and the wash, not in the vent settings. The alternative is that the pellets look acceptable, the specification sheet says nothing about intrinsic viscosity, and the customer finds out on the bottle.

Vacuum venting also gives the line a useful diagnostic, because the melt arrives at the vent either wet or dry. If it arrives wet, the dryer is the problem and the loss starts before the barrel. If it arrives dry and the pellets still come out short of IV, the loss is happening in the barrel and the conversation is about residence time and screw geometry. Two readings, two different conversations with whoever built the line.

Proving the Number Before the Balance Is Paid

The published test arrangement is straightforward: a free test on 10–20 kg of the buyer’s material, with video, measured output, specific energy and pellet photos sent before the balance is paid. For a PET pelletizing line I would want the pellet sample measured for intrinsic viscosity as well, and I would want it measured on material from your own wash line rather than on a clean reference flake. The machine proves its output; it does not prove your grade.

The risk sits with the supplier during that test. A run that lands more than 5% short of the agreed output leaves the deposit refundable. Together with the published IV loss figure of below 0.03 dl/g and the 500–2,000 kg/h band, that gives a buyer written conditions instead of verbal ones. The test hall has material storage, water and a 500 kVA supply, with three simultaneous material runs, so comparing two suppliers on your own material is a realistic exercise rather than a courtesy.

The comparison of the twelve platforms is the other document worth having open during that conversation, because it shows how the PET platform differs from the general-purpose pelletizers in the same catalogue and how the quality control data from a trial would slot into it. The granulator by material listing shows which platform was designed around which polymer, and PET is the awkward one. The relevant comparison is not the cheapest machine that can make pellets, but the one that makes your pellets at your moisture, with the IV your customer will pay for.

The published figures that define a food-grade rPET pellet

Intrinsic viscosity is the one number a PET buyer checks before anything else. The table sets the specification window against what each stage of the line does to it.

Figure Published value Where it applies
Bottle-grade rPET intrinsic viscosity 0.80–0.84 dl/g Purchase specification for food-grade output
Fibre-grade rPET intrinsic viscosity 0.70–0.78 dl/g Purchase specification for fibre-grade output
IV loss from moisture in the melt 0.01 dl/g per 100 ppm The mechanism the line is built around
TL-PET line IV loss Below 0.03 dl/g across 500–2,000 kg/h Supplier’s own published figure
Moisture target after crystallization Below 50 ppm Drying specification
Flake moisture for stable extrusion Below 0.5% Condition at the feed
Flake pH Below 8.0 Condition at the feed
Vacuum degassing pressure -0.08 to -0.1 MPa Vent specification

Questions buyers ask about this machine

Q1: What intrinsic viscosity does food-grade rPET need?

Bottle-grade rPET is specified at 0.80–0.84 dl/g and fibre-grade at 0.70–0.78 dl/g. The TL-PET line holds the loss caused during processing below 0.03 dl/g across its 500–2,000 kg/h band.

Q2: How much does moisture cost in intrinsic viscosity?

PET loses 0.01 dl/g of IV per 100 ppm of moisture, because water in wet flake triggers thermal hydrolysis in the melt. The polymer chain breaks permanently, so the loss cannot be recovered further downstream.

Q3: Can the line restore IV in already degraded flake?

No. The line controls the loss it causes, not the level of the incoming material. A pelletizing line cannot raise intrinsic viscosity, so sorting and washing set the starting point while the dryer and the vent protect it.

Q4: Does every PET pelletizing line need crystallization?

This one does. Crystallizing and underwater pelletizing capability was added in 2022 for food-grade rPET, and crystallization is what lets the dehumidifying dryer reach about 50 ppm at production speed.

Further reading on this site: comparison of the twelve platforms.

The rest of this series covers the same equipment from different angles: PET Pelletizing Line: What the Line Actually Contains, Sizing a PET Pelletizing Line Without Over-buying, PET Pelletizing Line Cost: Capital and Running Cost and PET Pelletizing Line Acceptance: The Test That Proves It.

About the author

Zhou Gong (周工) builds recycling lines at TENGLONG Plastic Machinery, a factory in Linyi, Shandong, with 18,000 m² of floor area, 30-plus staff and 820-plus lines delivered to 46 export markets. I keep a moisture meter in my pocket when I commission a PET line, because it settles arguments that no pellet photograph ever will. The numbers in this article come from test runs and from dated published sources, not from a sales sheet.

If you want a recommendation rather than a catalogue, send the material form, the contamination level and the target output. We return a model and a price range within one working day, and the test run on 10-20 kg of your own material is free before the balance is paid.

Related reading

العربيةAR