CE marked · ISO 9001:2015 · 18-month warranty

· products · By

Extruder Screw Diameter and Length: How to Match It

Screw diameter sets the output ceiling and the L/D ratio sets the melting capacity. The arithmetic for matching both to the machine and the material.

Diameter sets the output ceiling, because output is what the screw displaces per revolution multiplied by the speed it turns at. Length sets the melting capacity, because a longer screw at the same diameter holds the melt longer and builds a steadier pressure profile. The two are chosen together, with the gearbox, the barrel and the drive.

The published single screw granulator covers 150-700 kg/h on a 90-150 mm nitrided screw, so the pairing in the catalogue is the reference. Diameter also reaches back into your schedule: published nitrided screw and barrel lead times run 40-50 days at Φ20 to Φ90 and over 70 days at the largest sizes.

Sizing the screw to the duty

  • Diameter sets the output ceiling and the gearbox has to match it.
  • L/D sets melting capacity and adds shear, so the material must take it.
  • Published pairing: 150-700 kg/h on a 90-150 mm nitrided screw.
  • Lead time grows with diameter, from 40-50 days up to over 70 days.
3D product render of a TENGLONG plastic pelletizing machine on a white background, shown here as a visual reference for screw diameter and length.
3D product render of a TENGLONG plastic pelletizing machine on a white background, shown here as a visual reference for screw diameter and length.. Used here as a visual reference for extruder screw diameter and length against machine output. Rendering, not a photograph of a customer plant.

Diameter comes first

Screw diameter sets the output ceiling of a single screw extruder, because output is the volume the screw displaces in one revolution multiplied by the revolutions per minute. Diameter is the main lever on that displacement, and it also decides how much torque the gearbox has to carry and how much material the feed section has to swallow at once.

The published single screw granulator in this range covers 150-700 kg/h with a 90-150 mm nitrided screw, and that pairing gives you the arithmetic directly. Capacity across the platforms runs 100-3,000 kg/h. Moving from a workshop machine to an industrial line is not a matter of fitting a bigger motor; the diameter of the wear part moves with it, and so does the barrel around it.

Diameter also decides how hard the wear part works. A larger screw moves more material through the same length of barrel per revolution, so the abrasive load on the flight and the bore rises with the throughput. That is why the published barrel life of 1-5 years in high-filler PVC extrusion should be read against the diameter and the running hours rather than treated as a fixed number for every machine.

Length and the L/D ratio

Rendered trade-show scene with a TENGLONG ABS plastic granulator and visitors at the exhibition booth, shown here as context for the equipment on a trade-show floor at an extruder screw and barrel.
Rendered trade-show scene with a TENGLONG ABS plastic granulator and visitors at the exhibition booth, shown here as context for the equipment on a trade-show floor at an extruder screw and barrel.. Shown here as production context. Rendering, not a photograph of a customer plant.

Length is the second number, and it is written as L/D, the length of the screw over its diameter. A 40:1 ratio, as published for the twin screw extruder line, means a long screw in a modest bore. Length buys residence time, and residence time buys melting capacity and a pressure profile that stays steady instead of hunting.

The trade is shear and heat history. A long screw that holds a stable melt gives the wear pair a gentler life per tonne, because the melt is not being dragged through a worn channel harder than it has to be. A short screw pushing a high output does the opposite, and the flight and the bore absorb the difference in wear.

Length also changes what the drive end has to absorb, because a long screw that runs out of true vibrates in the bore and wears a pattern rather than a smooth surface. Published straightness for a nitrided screw is 0.015-0.02 mm, and the bore has to be equally true, because a screw running eccentric sees the clearance change all the way round the flight.

Matching diameter and length to the machine

Take the machine first and the screw second. The single screw granulator at 150-700 kg/h takes a 90-150 mm nitrided screw. The twin screw extruder line runs 300-1,500 kg/h at 40:1 L/D for filled and reinforced compounds. The two stage granulating line runs 300-1,200 kg/h for high-contamination waste at 60-100 mesh. Each platform has its own combination, and they are not interchangeable.

Then take the material, because the contamination sets the screen duty and the screen duty sets the melt that reaches the screw. A single screw machine working at 60-80 mesh is being asked to handle about 2% non-melting contamination, while a two stage line at 100 mesh handles 5-8%. Where the feed sits above 8%, washing is cheaper than filtering and the screw choice follows from that decision rather than the other way round.

Finally take the pellet size you intend to sell. The default is 3 mm for injection and blow moulding, 2-2.5 mm for film and cable, and 4 mm for large mouldings. Die hole diameter and land length set that size, and the melt arriving at the die has to be steady for the cut tolerance to hold at +/-0.2 mm on a strand cutter and +/-0.15 mm underwater.

Diameter sets the delivery date

Screw size reaches back into the production plan. Published nitrided screw and barrel lead times run 40-50 days for diameters from Φ20 to Φ90, 50-60 days for Φ90 to Φ180, 60-70 days for Φ180 to Φ250, and over 70 days at the largest sizes. A plant that sizes up for more output is also booking a longer wait for the wear parts that keep it running.

This is why the spare parts policy matters more than the spare parts price. Wear parts are stocked for three years, and one spare screw ships with the line. A screen change takes 20 minutes, so the screening routine is a scheduled 20-minute job every 3-4 hours. A screw change is a different order of event, and the stock on the shelf is what keeps it a plan rather than an outage.

Plan the changeover against the published 20-minute screen change and the 8-hourly blade check, and the wear parts stay ahead of the wear. Plan it loosely and the plant meets the published delivery time on the day the screw gives up. At Φ180 to Φ250 that is a production problem measured in months, not an afternoon.

The sizing arithmetic to run first

Before you ask for a quotation, write down the numbers that matter: the material and its contamination level, the output you need in finished bagged pellets averaged over four hours, the screen mesh you intend to run, and the pellet size you intend to sell. Those fix the diameter, the L/D ratio and the wear specification, and a supplier who cannot fill them in has not read your feed.

Add the running hours to that list, because it changes the answer. Continuous running on filled compound is a different screw duty from light running on clean regrind, at the same diameter and the same output. Wear data is always quoted against a duty, so the duty has to be stated or the answer will be quoted against somebody else’s material.

Then compare against the published platforms rather than against a supplier’s best week. The twelve model comparison on the site lists capacity and the screw or mesh figure for each platform, and capacity across the range is 100-3,000 kg/h. At the top of that range the plastic granules production line runs 500-3,000 kg/h as a turnkey package, where the screw is one element of the chain rather than a free choice.

Published capacity and screw figures by platform

Diameter sets output and length sets the melt quality you can reach. The table pairs the two against the throughput each machine is rated for.

Platform Capacity Screw or duty figure
TL-SJ single screw granulator 150-700 kg/h 90-150 mm nitrided screw
TL-TS twin screw extruder line 300-1,500 kg/h 40:1 L/D, filled compounds
TL-2S two stage granulating line 300-1,200 kg/h 60-100 mesh, high contamination
TL-PM plastic pellet mill 100-500 kg/h Compact skid, in-house scrap
TL-MB masterbatch granulator 20-500 kg/h 20-60% pigment loading
TL-FK flakes pelletizing machine 300-1,000 kg/h Washed HDPE/PP flake, 80-100 mesh

What buyers ask us before they order

Q1: How do I work out which screw diameter I need?

Start from the output you need in finished bagged pellets averaged over four hours, then read it against the published pairings. A single screw granulator at 150-700 kg/h takes a 90-150 mm nitrided screw, so diameter and output are selected together rather than one after the other.

Q2: What does the L/D ratio actually change?

It changes how much melting and how much pressure the screw can develop. The twin screw extruder line here is published at 40:1, which gives a long residence path. The cost is more shear and more heat history on the melt, so the material has to be able to take it.

Q3: Does a bigger screw always mean more output?

It means more capacity, and it also means a larger gearbox, a larger motor and a longer wait for the wear part. Published lead times run 40-50 days for Φ20 to Φ90 and over 70 days at the largest sizes, so size up only if the running hours justify it.

Q4: How much lead time should I allow for a screw order?

Published nitrided screw and barrel lead times run 40-50 days for Φ20 to Φ90, 50-60 for Φ90 to Φ180, 60-70 for Φ180 to Φ250, and over 70 days for the largest sizes. Plan the first replacement on the same clock, because the wear does not wait for the paperwork.

The companion write-ups for this machine family are: Extruder Screw and Barrel: What the Part Does, Nitrided vs Bimetallic Extruder Screw: Which to Buy, Screw and Barrel Cost: Replacement and Total Cost and Screw Inspection and Commissioning: A Working Routine.

About the author

Zhou Gong (周工) signs off the test runs at TENGLONG Plastic Machinery, 18,000 m² of plant in Linyi, Shandong, with 30-plus staff and 820-plus lines delivered to 46 export markets. I would rather quote a screw one size down with the honest output figure than a bigger screw the gearbox cannot carry. Every number in this piece is traceable: measured on our own machines, or published with the date it was checked.

Send us the material form and the target output and we will come back inside one working day with the machine that fits and what it costs. The free test on 10-20 kg of your own material comes before the balance is paid, and a measured output more than 5% below the agreed figure leaves the deposit refundable.

Related reading

العربيةAR