Screen life on dirty film is one of the largest variable costs in pellet production. The TL-2S holds an 80 to 100 mesh pack for four to six hours because stage one filters at modest pressure, against 20 to 30 minutes on a single long extruder.
Count the true cost of a change: the pack, the operator time and the off-spec product made while conditions stabilise. On short intervals the off-spec material usually costs more than the other two. Stage two keeps die pressure and pellet size steady as the pack loads.
Screen life as a cost
- Four to six hours is the published dirty-film interval.
- A finer mesh loads faster; use it only when the pellet spec needs it.
- Off-spec product is usually the largest cost of a screen change.
- Record start and end pressure by flake source to manage the interval.

Screen life is a cost, not a nuisance
On dirty agricultural film, screen life is one of the largest variable costs in pellet production. A pack that lasts four hours and one that lasts forty minutes produce very different amounts of saleable pellets from the same machine in the same shift.
The TL-2S is designed around that fact. Stage one filters at modest pressure through an 80 to 100 mesh double-piston changer, and the published life is four to six hours. A single long extruder on the same feedstock blinds a pack every 20 to 30 minutes.
The difference comes from pressure and from the separation of jobs. Filtering at low pressure lets the pack load gradually rather than being forced, and stage two builds die pressure afterwards from clean melt.
What changes the interval

The first variable is the mesh. A finer pack catches more contamination and loads faster. Eighty to 100 mesh is the standard range for dirty film; going finer should follow a measured requirement in the final pellet rather than a general desire for cleanliness.
The second is the dirt in the film. Sand and soil load a pack faster than label paper. A load from a wet season can carry substantially more soil than the same collection stream in a dry month, and the interval should be reviewed with the season.
The third is throughput. Running a line above its rated output pushes more contamination through the same area in the same time. The published intervals assume the stated output range, not a stretched machine.
Counting the true cost of a change
A screen change has three costs: the pack, the operator time and the off-specification product made while pressure and melt conditions re-stabilise. On a line with short intervals the third cost often exceeds the first two.
The double-piston changer keeps one station online while the other is serviced, which reduces the line stop. An automatic back-flush changer is offered for 100 mesh and finer duty where the interval would otherwise be too short.
Calculate cost per tonne by dividing the total change cost by the tonnes produced between changes. That number is comparable across meshes and across machines, unlike a screen life figure quoted in hours alone.
The interaction with pellet size
As a pack loads, a single extruder loses die pressure and pellet size drifts. On the TL-2S, stage two rebuilds 80 to 120 bar from filtered melt, so pellet size holds within plus or minus 0.2 mm across the interval.
A melt pump on stage two tightens pellet weight further to plus or minus 0.3%. It is a refinement, but it becomes attractive when the interval is long and the customer has a tight specification.
If pellet size does drift during a campaign on a two-stage line, the cause is more likely a stage-two issue or a cutter setting than the screen. The value of the design is that it removes the screen from that equation.
Building a filtration record
Record pressure at the start and end of every interval, along with the flake source and the mesh. After a month the record shows which loads are expensive and whether the pack choice is right.
Use the record in supplier discussions. If one collection stream consistently halves the screen life, the price of that feedstock should reflect the cost it imposes on the line.
Our factory test procedure establishes the starting interval on your own film. Treat that number as a baseline to be managed, not a guarantee that holds for every load.
Screen life and its drivers
Screen life on dirty film is a cost input, not a nuisance. The table shows how mesh choice changes the hourly picture.
| Factor | Effect on interval | Response |
|---|---|---|
| 100 mesh pack | Shorter than 80 mesh | Use only if pellet spec needs it |
| Sand and soil | Faster loading | Upstream washing or coarser pack |
| Above-rated output | More dirt per hour | Return to rated range |
| Double-piston changer | One station stays online | Shorter line stop |
| Back-flush option | Extended fine filtration | For 100 mesh and finer |
Common questions, with short answers
Q1: How long does a screen last on dirty film?
Four to six hours on the TL-2S with an 80 to 100 mesh pack. A single long extruder on the same feedstock can blind the pack every 20 to 30 minutes.
Q2: Should I use 100 mesh on agricultural film?
Only if the pellet specification needs it. A finer pack loads faster and shortens the interval. The standard range is 80 to 100 mesh, chosen against the actual contamination and the required pellet quality.
Q3: What does a screen change really cost?
The pack, the operator time and the off-specification product made while conditions re-stabilise. On short intervals the off-spec material usually costs more than the other two combined.
Q4: Does screen loading change pellet size?
Not on a two-stage line. Stage two rebuilds die pressure independently of the screen, holding pellet size within plus or minus 0.2 mm. On a single extruder, size drifts as the pack loads.
Where this fits in the wider range: plastic recycling equipment and the twelve-platform comparison.
Read next, if the same model is going on your line: Two-Stage Die Pressure: Why Pellets Hold 0.2 mm, What a Cutter-Compactor Does: 60 to 300 kg/m3, How Wet Can Film Be Before You Need a Press and When a Single Screw Beats a Two-Stage Line.
About the author
Zhou Gong (周工) is a recycling machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong, where 30-plus staff work across 18,000 m² and 12 machine platforms covering 100 to 3,000 kg/h. Hours alone tell you little. I want the cost per tonne between changes. Every figure used here has been measured on a machine or taken from a dated published source, not from a brochure.
Send the material form, the contamination level and your target output to our engineering team and you get a model and a price range within one working day. A test run on 10–20 kg of your own material is free, and if the measured output misses the agreed figure by more than 5%, the deposit is refundable.