A PET washing line is a sequence of separations, and each stage exists because the next one cannot cope with what the previous one left. The label remover takes off sleeves and paper; the sink-float tank takes off the PP and PE caps and rings that float; the hot caustic wash takes off glue, oil and organic residue; the friction washer takes off what is still stuck on; and the dewatering and drying stage takes off the water. Ask each stage to remove something it was not designed for and the whole line slows down.
The published 2026 price bands are wide because the configurations are wide. A cold wash line at 1,000–2,000 kg/h is listed at US$150,000–300,000; adding hot wash, sink-float and drying takes it to US$200,000–400,000; and a food-grade line with optical sorting and closed-loop water treatment runs to US$350,000–600,000. Budget a further 15–25% on top for water treatment and commissioning.
What each stage is for
- Label remover: US$2,000–30,000, 500–5,000 kg/h, published label removal rate 95–99%.
- Sink-float tank: US$18,000–65,000 FOB Shanghai, 500–3,000 kg/h, and the stage that removes the polyolefin fraction.
- Hot caustic wash: 85–95 °C, 1–2% caustic soda, 30–45 minutes per batch.
- The whole line uses 18–30 kWh per ton of flake and 0.8–1.2 m³ of water per ton, and delivers flake at below 1–2% moisture after drying.

The stage map, and why each stage exists
A PET washing line is a chain of eight or nine stages, and each one exists to remove something the previous stage could not. Confusing the stages is the most expensive mistake in this business, because it usually means buying the wrong machine twice.
Bale breaking and pre-wash removes wire, strapping, sand and grit. It is the stage most often underestimated, and it protects every machine downstream: sand that reaches a wet crusher destroys the blades, and dirt that reaches a hot washer gets cooked onto the flake instead of washed off it.
Label removal strips sleeves, shrink labels and paper labels from whole bottles, before crushing, because a sleeve on an intact bottle is far easier to remove than the same sleeve on a flake. Published figures put label removal rates at 95–99% for modern machines, with throughput from 500 kg/h to 5,000 kg/h.
Wet crushing cuts bottles into 8–16 mm flake in a water bath, which suppresses dust, cools the material and starts the wash. The screen size set here determines how much work every downstream stage has to do.
Sink-float separation exploits density. PET has a density of about 1.38 g/cm³ and sinks; PP and PE sit below 1.0 g/cm³ and float, and are skimmed off. Published separation rates are 95–99% of the floating fraction.
Hot caustic washing at 85–95 °C with 1–2% caustic soda and a surfactant breaks down glues, oils and label adhesives. This is the stage that decides whether the flake is food-grade or fibre-grade, and it is the most expensive stage to add later.
Friction washing scrubs the flake surface at high shear with counter-current water. Rinsing removes the caustic, because caustic carried into drying leaves alkaline residue and raises the risk of hydrolysis during melting. Dewatering and drying bring the moisture down below 1–2%.
What a line actually delivers, against the nameplate

The published performance figures for a 1,000–2,000 kg/h PET washing line are worth reading carefully, because the gap between the nameplate and the floor is the number that determines whether a business works.
Real throughput runs 60–80% of nameplate. Water use with recirculation is 0.3–1.5 m³ per ton; energy use is 18–30 kWh per ton; flake moisture after drying is below 1–2%; PVC content for food grade is below 50 ppm; and final purity reaches 99.5%+ with optical sorting.
Two consequences follow. The first is that a line quoted at 2,000 kg/h on a machine spec’d at 2,000 kg/h is selling the brochure, not the floor. The second is that each stage should be sized 20–30% above the target throughput, because a 2,000 kg/h shredder beside a 2,000 kg/h washer does not make a 2,000 kg/h line.
Water is the item that catches new operators. A washing line without closed-loop recirculation drinks more than 3 m³ per ton and discharges contaminated wastewater, which in most places is a permit violation within weeks. Budgeting 15–25% of the line cost for water treatment is the number the industry quotes, and it pays back quickly.
What the configurations cost
Published 2026 price bands for PET washing lines give a useful frame, because the spread between the cheapest and the most expensive configuration is where most of the decisions sit.
A basic cold-wash line at 1,000–2,000 kg/h runs US$150,000–300,000. Adding hot wash, sink-float and drying moves it to US$200,000–400,000. Adding optical sorting and closed-loop water treatment puts a full food-grade line at US$350,000–600,000. On top of that, allow a further 15–25% for water treatment and commissioning.
The line-level equipment costs sit inside those totals. A float tank is US$18,000–25,000 for a 500 kg/h stainless 304 unit, US$28,000–40,000 at 1,000 kg/h and US$45,000–65,000 at 1,500 kg/h, all FOB Shanghai, with published payback periods of 4–9 months depending on configuration. A label remover is US$2,000–11,000 for small units and US$15,000–30,000 for industrial machines.
One published comparison is worth keeping in mind: upgrading the flake contact parts to 304 stainless adds about US$16,000 to a standard 500 kg/h configuration. For a food-grade line that is not an optional extra, it is the whole point of the line.
Cold wash or hot wash: the decision that cannot be reversed
This is the single most consequential choice on a PET washing line, because it determines who you can sell to.
Cold wash works at ambient temperature with mild agitation. It removes surface dirt and soluble residues, and it cannot remove glue, oil or food residue. Published purity is 98–99%, and the output sells to fibre, strapping and sheet producers. Energy cost is low.
Hot wash at 85–95 °C with caustic removes glue, oil and organic residues. Published purity is 99.5%+, and the output sells to bottle-to-bottle converters working under EU PPWR rules. Energy cost is high, because water heating dominates.
The trap is the upgrade path. Technically you can start cold and add hot wash later. Practically, you cannot: hot wash needs heat exchangers, insulated tanks and caustic dosing that a cold-wash line does not have, and retrofitting costs more than building it in. If food grade is even a maybe in your plan, specify hot wash now.
The second trap is the pre-sort. If contamination reaches the hot washer, you are cooking glue into the flake instead of washing it off. Front-end sorting is always cheaper than back-end reprocessing.
PET washing stages: what each removes and its 2026 cost band
Each stage of a washing line has a published price band and a specific job, and the two go together.
| Stage | Removes | Published cost |
|---|---|---|
| Label remover | Sleeves, paper labels, some caps | US$2,000–30,000; 500–5,000 kg/h |
| Sink-float tank | PP/PE caps, rings, label scraps | US$18,000–65,000 FOB Shanghai; 500–3,000 kg/h |
| Hot caustic wash | Glue, oil, organic residue | Part of the line total; 85–95 °C, 1–2% caustic |
| Friction washer | Stubborn surface contamination, residual glue | Part of the line total |
| Rinsing | Residual caustic, detergent, fines | Part of the line total |
| Dewatering and drying | Free water, then bound moisture | Moisture below 1–2% after drying |
What buyers ask us before they order
Q1: How much does a PET washing line cost in 2026?
A basic cold-wash line at 1,000–2,000 kg/h runs US$150,000–300,000. With hot wash, sink-float and drying it is US$200,000–400,000, and a full food-grade line with optical sorting and closed-loop water treatment lands at US$350,000–600,000. Add a further 15–25% for water treatment and commissioning.
Q2: What throughput should I expect from a 2,000 kg/h line?
Real throughput runs 60–80% of nameplate, so 1,200–1,600 kg/h. Published line figures are 800–1,700 kg/h on a machine spec’d at 1,000–2,000 kg/h. Anyone quoting you the full nameplate is selling the brochure rather than the floor, which is why each stage should be sized 20–30% above target.
Q3: Can I start with cold wash and upgrade to hot wash later?
Technically yes, practically no. Hot wash needs heat exchangers, insulated tanks and caustic handling that a cold-wash line does not have, and the retrofit costs more than specifying it at the start. If food grade is even a possibility, build for hot wash now.
Q4: How much water does a PET washing line consume?
0.3–1.5 m³ per ton of flake with recirculation. Without closed-loop recirculation the figure is over 3 m³ per ton and the wastewater discharge is a permit problem in most jurisdictions. We size water treatment to recirculate about 90% of the water, and budget 15–25% of line cost for it.
Related pages on this site: PET pelletizing line, plastic granules production line, granulator by material and turnkey pelletizing solutions.
If you are working through the same machine family, these are the other Sink-Float Separation Tank: How PET Is Separated, Hot Washing Machine for PET: Temperature and Caustic, How to Choose a PET Washing Line for Your Material and PET Washing Line Maintenance: Five Costly Failure Modes.
About the author
Zhou Gong (周工) is a recycling machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong, where 30-plus staff work across 18,000 m² and 12 machine platforms covering 100 to 3,000 kg/h. The question I ask a customer who is comparing two washing lines is who buys the flake. Fibre grade and bottle-to-bottle are different plants, and the quotation that ignores that difference is quoting the wrong line. Every figure used here has been measured on a machine or taken from a dated published source, not from a brochure.
Send the material form, the contamination level and your target output to our engineering team and you get a model and a price range within one working day. A test run on 10–20 kg of your own material is free, and if the measured output misses the agreed figure by more than 5%, the deposit is refundable.