CE marked · ISO 9001:2015 · 18-month warranty

· products · By

Hot Washing Machine for PET: Temperature and Caustic

A PET hot wash runs at 85–95 °C with 1–2% caustic soda for 30–45 minutes. How to calculate the caustic dose and where the energy goes.

The hot wash stage exists for one reason: to break down the adhesives that hold labels, glue and food residue to the PET, and that needs heat, alkali and time together. The published operating window is 85–95 °C with 1–2% caustic soda and a specialist surfactant, held for 30–45 minutes per batch. The setpoint is a specification, not a minimum — a tank running at 80 °C is not a hot wash with a tolerance, it is a wash that is not doing its job.

Caustic is consumed, not merely diluted, so the concentration has to be made up daily and measured rather than assumed. And the energy question has a simple answer: water heating dominates. A complete line runs at 18–30 kWh per ton of flake, so heat recovery from the rinse water is the single largest lever on the running cost.

The operating window and the two things to watch

  • 85–95 °C, 1–2% NaOH, 30–45 minutes per batch — that is the published window.
  • The caustic setpoint is a specification; a tank at 80 °C is not running a hot wash.
  • Make caustic up daily and measure it. Consumption tracks contamination carried in.
  • Water heating dominates the 18–30 kWh per ton of flake, so heat recovery is the first lever, not the last.
Rendered scene of a TENGLONG workshop with a green machine and a visitor inspecting it
Rendered scene of a TENGLONG workshop with a green machine and a visitor inspecting it. Shown here as production context. Rendering, not a photograph of a customer plant.

What the hot wash actually does

The hot wash is the chemical heart of a PET line. Everything else is physical separation; this stage is where contaminants are chemically destroyed rather than mechanically removed.

PET bottles carry three classes of trouble. There is loose dirt, which the pre-wash handles. There is label adhesive — hot-melt glues and pressure-sensitive adhesives — which is chemically bound to the PET surface and needs heat plus alkali to release. And there is food residue and oil, which needs heat and surfactant.

Published operating conditions are 85–95 °C with 1–2% caustic soda and a specialist surfactant, with a wash time of 30–45 minutes per batch. The temperature and the concentration are tuned to the label chemistry of the local bottle mix, which is why a line that works in one country often needs adjustment in another.

Calculating the caustic dose

Rendered scene of a TENGLONG exhibition booth with a green conveyor line and visitors
Rendered scene of a TENGLONG exhibition booth with a green conveyor line and visitors. Shown here as production context. Rendering, not a photograph of a customer plant.

The dose is not a fixed number, and treating it as one is the most common reason a hot wash underperforms.

The working calculation is: caustic mass per batch = tank volume × water density × target concentration. A 10 m³ tank at 1% caustic needs 100 kg of NaOH per full charge. The heat required to raise that tank to 90 °C, and then to hold it there against heat loss into the flake and the shell, determines the heater size and the energy cost.

Two practical points follow from the arithmetic. First, the tank has to be heated for the whole batch cycle, so a larger tank with the same throughput holds a larger caustic inventory and a larger heating duty — which is why the published comparison lists the hot wash reactor and heater as sized specifically to give enough residence time at temperature for the target throughput. Second, caustic is a consumable that has to be dosed and made up, and it has to be neutralised or handled properly at discharge.

Concentration above the target is not better. Excess caustic at high temperature attacks the PET itself. The published 85–95 °C with 1–2% caustic window is a specification to hold, not a floor to exceed.

Heat recovery and where the energy goes

A hot wash line is a thermal plant, and the energy cost is dominated by water heating rather than by pumps or agitation. Published energy use for a complete PET washing line is 18–30 kWh per ton of flake.

That figure is the reason heat recovery changes the economics of the whole line. The hot wash discharge is hot and carries caustic, so it cannot simply go to the cold rinse tank. But the sensible heat can be recovered into the incoming water, which reduces both the heater size and the energy bill.

Which is exactly why retrofitting hot wash onto a cold-wash line is difficult. A cold-wash line has no heat exchanger, no insulation on the wash tank, no caustic dosing system and no caustic handling in its layout. Adding those means changing the line, not adding a machine to it. The published guidance is blunt about this: if food grade is even a maybe, specify hot wash upfront or replace the line.

Running the stage well

Four operating habits separate a hot wash that works from one that underperforms quietly.

Hold the temperature, not just set it. Temperature control at 85–95 °C is the specification; a tank that drifts to 78 °C still cleans, just less well, and nobody notices until the customer complains about glue.

Watch the caustic concentration, not just the dose. Caustic is consumed by the contaminants it is dissolving and carried out with the wash water. Dosing to a setpoint once per batch is not enough; it needs monitoring and make-up.

Watch the residence time. The published 30–45 minutes per batch is a range, and the material that needs it is the material that determines the tank size. A tank sized for the fast case will under-wash the difficult one.

Do not skip the pre-sort. Contamination that reaches the hot washer gets cooked onto the flake instead of washed off it, and it is much cheaper to remove it before the wash than after it.

Hot wash operating window

The operating window for the hot wash stage, and the note against each parameter that explains what happens outside it.

Parameter Published range Note
Water temperature 85–95 °C Setpoint is a specification, not a minimum
Caustic soda 1–2% NaOH Consumed by contamination and carried out
Wash time per batch 30–45 minutes Sets the tank size at target throughput
Surfactant Specialist grade Tuned to the local label chemistry
Line energy use 18–30 kWh per ton of flake Water heating dominates

Questions buyers ask about this machine

Q1: What temperature and caustic concentration does a PET hot wash need?

Published operating conditions are 85–95 °C with 1–2% caustic soda and a surfactant, for 30–45 minutes per batch. The window is tuned to the label chemistry of the local bottle mix, and running above the caustic target is not an improvement — excess alkali at high temperature attacks the PET.

Q2: How much caustic does a hot wash tank need?

Caustic mass per batch = tank volume × water density × target concentration. A 10 m³ tank at 1% needs 100 kg of NaOH per charge, and that figure has to be topped up through the cycle because caustic is consumed by the contaminants and carried out with the wash water.

Q3: Can hot wash be retrofitted to an existing cold-wash line?

Practically, no. A cold-wash line has no heat exchanger, no insulated wash tank, no caustic dosing and no caustic handling, and retrofitting those costs more than building a hot-wash line from the start. If food-grade output is even a possibility, specify hot wash at the outset.

Q4: What does the hot wash stage do to the energy cost of the line?

It dominates it. Published energy use for a complete PET washing line is 18–30 kWh per ton, and water heating rather than pumps or agitation is the main component. Heat recovery from the hot discharge into the incoming water is what brings that figure down in a well-designed line.

The pages that come up most often alongside this one: plastic granules production line and applications by industry.

The companion write-ups for this machine family are: PET Washing Line: What Each Stage Removes and Costs, Sink-Float Separation Tank: How PET Is Separated, How to Choose a PET Washing Line for Your Material and PET Washing Line Maintenance: Five Costly Failure Modes.

About the author

Zhou Gong (周工) is the recycling machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong — a plant of 18,000 m² with 30-plus staff, 12 platforms and 820-plus installations across 46 export markets. I ask for the tank temperature log before anything else when a hot wash is underperforming: nine times out of ten it has been drifting slowly upward because nobody ever set it back. Where a figure is quoted here it has been measured or published with a date attached; nothing in this article is an estimate.

The quickest way to a real answer is to send the feed form, the contamination level and the throughput you need. A model and a price range come back within one working day, the trial on 10–20 kg of your material is free, and a result that misses the agreed output by more than 5% leaves the deposit refundable.

Related reading

العربيةAR