Mass flow moves every particle in the silo; funnel flow moves only the core and leaves the wall material behind. For plastic pellets the published practice is mass flow, and the pattern is decided by three numbers: the cone half-angle, the outlet diameter and the wall finish.
The cost of getting it wrong is not abstract. Funnel flow creates dead zones where material sits for weeks, and a design without adequate flow systems can leave 30–40% of the silo stagnant. Breaking the rathole that follows costs four to eight labour hours per incident, which is where the 15 to 20% mass-flow premium earns its keep.
Three numbers decide the flow
- Mass flow needs a cone half-angle of at least 60°, and 65 to 70° for regrind blends.
- The outlet should be 300–400 mm across, six to eight times the largest particle.
- Wall finish of 2B or better on stainless steel, because a rough wall grows a dead zone.
- A poor flow design can leave 30–40% of the silo standing stagnant for weeks.

What the Two Patterns Are
Mass flow and funnel flow describe two different ways material can leave a silo, and the choice between them is made before a single sheet of steel is cut. In mass flow the whole contents of the vessel move together, top to bottom, with every particle travelling. In funnel flow the material in the middle drops out through the outlet while material at the walls stays where it is, in what are called dead zones.
For plastic pellets, published practice points at mass flow. The standard cone angle for plastic pellets is 60°, and 67° is used for slightly cohesive or flaky granules. Funnel flow is not a design anyone specifies deliberately for pellets; it is what you get when the vessel geometry is wrong for the material, which is why it shows up as a running fault rather than a drawing decision.
The consequence of getting it wrong is measurable. Funnel flow creates dead zones where material sits for weeks, and a design that lacks adequate flow systems can leave 30–40% of the silo stagnant. That material ages in the vessel while the rest of the stock turns over, and the two are not the same product when they finally reach the same bag.
The Cone Angle Decides It

Mass flow needs a cone half-angle of at least 60° from horizontal, and 65 to 70° for regrind blends. That single dimension is the difference between a material that slides along the wall and one that hangs on it. There is no clever lining, no coating and no agitator that substitutes for getting the angle right in the first place.
The angle also has to suit the material, not the average of the recipe. Clean moulded spheres and an irregular regrind blend do not have the same wall friction, which is why the published figure is 65 to 70° for regrind blends rather than the 60° used for plastic pellets. When a plant changes what it runs, the cone angle is a decision that has to be revisited.
There is a price for the steeper cone, and it is worth paying deliberately rather than discovering later. A mass-flow cone adds roughly 15 to 20% to the fabricated shell cost but removes the need for manual rathole breaking. That is a trade between steel that costs more and labour that stops, and the second half of it only becomes visible once the silo has been running for a month.
The Outlet and the Wall Finish
The outlet is the second half of the flow decision. Mass flow needs an outlet 300 to 400 mm across so it is six to eight times the largest particle. Get that ratio wrong and the material arches over the opening regardless of how good the cone is, which is why an outlet size belongs in the specification next to the angle rather than in the fabricator’s discretion.
The particle size comes from the cutter upstream. Pellet size is 3 mm by default for injection and blow moulding, 2–2.5 mm for film and cable, and 4 mm for large mouldings, with strand cutting held to ±0.2 mm and underwater cutting to ±0.15 mm. A silo designed for one pellet size does not automatically suit another, and the outlet rule has to be checked against the product actually intended for storage.
The third requirement is the wall finish, and it is the one most often left vague. Published practice calls for 2B or better on stainless steel. It is not a cosmetic clause: a wall that holds material is a wall that grows a dead zone, and the dead zone is exactly what a mass-flow design was supposed to remove.
What a Stagnant Silo Costs
The cost of funnel flow is paid in labour, at the worst possible moment. Clearing a rathole by hand runs four to eight labour hours per incident at US$85 an hour. It happens on a weekend or at the start of a shift, it happens with the pelletizer stopped, and the operator doing it is standing next to a vessel full of material that has already shown it will not move.
Run the annual bill and the case for mass flow becomes plain, which is why published payback on a mass-flow cone is put at four to seven months. A silo that needs two rathole incidents a year, at four to eight hours each, at US$85 an hour, has already spent most of the premium the cone cost.
There is a safety argument too, and it is the one a plant manager will raise first. A silo that has ratholed is a silo somebody has to open and clear by hand, in a confined space, over loose pellets that have already proved they will not move on their own. That risk appears in none of the published cost figures, and it is priced in no quotation.
Deciding the Pattern for Your Material
The decision rule is short. Free-flowing moulded pellets get mass flow with a cone half-angle of at least 60°. Regrind blends get 65 to 70°. Slightly cohesive or flaky granules get 67°. In every case the outlet has to be six to eight times the largest particle, and the wall finish has to be 2B or better.
Check the material against the rule rather than the other way round. A masterbatch granulator produces pigmented pellets whose behaviour is not identical to natural resin, and a flakes pelletizing machine works on washed flake whose shape is decided upstream in the size reduction stage. The material guide on this site is a reasonable starting point for the general behaviour of each polymer, but the flow geometry still has to be set against your own pellets.
One last point on specification. The flow pattern should appear in the quotation as numbers: a cone half-angle, an outlet diameter, a wall finish. Any body that sells vessels without those three figures is selling a shape rather than a flow system, and the difference between the two shows up in the first month of production rather than on the delivery note.
Mass flow and funnel flow, side by side
Mass flow and funnel flow are not two preferences, they are two different machines inside the same shell. The table compares what each one does to the material.
| Aspect | Mass flow silo | Funnel flow silo |
|---|---|---|
| How the material moves | Every particle moves, top to bottom | Only the core moves; wall material stays |
| Cone half-angle | At least 60° from horizontal | Steep walls and a narrow outlet cause it |
| Outlet | 300–400 mm, six to eight times the largest particle | Small outlet, material arches over it |
| Material left behind | None, the vessel empties | Dead zones where material sits for weeks |
| Stagnant fraction | No stagnant zone to speak of | 30–40% of the silo can stand stagnant |
| Labour consequence | No manual rathole breaking | Four to eight labour hours per incident at US$85 an hour |
| Capital effect | 15–20% more on the fabricated shell | Cheaper shell, more labour later |
What buyers ask us before they order
Q1: What is the difference between mass flow and funnel flow in a silo?
In mass flow every particle in the silo moves. In funnel flow the core of the material moves while material at the walls stays in dead zones, and a design without adequate flow systems can leave 30–40% of the silo stagnant.
Q2: What cone angle do plastic pellets need?
Mass flow needs a cone half-angle of at least 60° from horizontal, with 65 to 70° for regrind blends. Sixty degrees is the standard cone angle for plastic pellets and 67° suits slightly cohesive or flaky granules.
Q3: How much does a mass-flow cone add to the price?
Roughly 15 to 20% on the fabricated shell cost. It removes the need for manual rathole breaking, which costs four to eight labour hours per incident at US$85 an hour, giving a published payback of four to seven months.
Q4: Does a mass-flow silo need a special wall finish?
Yes, a wall finish of 2B or better on stainless steel. The surface has to be smooth enough that material slides rather than hangs on the wall, because a wall that holds material grows a dead zone.
The rest of this series covers the same equipment from different angles: Pellet Storage Silo: What It Does on a Pelletizing Line, How Big Should Your Pellet Storage Silo Be, Pellet Silo Cost: Vessel, Discharge and Installed Price and Silo Commissioning: Level, Discharge and Acceptance.
About the author
Zhou Gong (周工) works on the screw and barrel line at TENGLONG Plastic Machinery, which began in 2016 as a workshop serving recycling plants around Linyi and now ships 820-plus lines to 46 export markets. I would rather argue about a cone angle for an hour than take a rathole call at three in the morning, and the cone angle is the cheaper conversation. Nothing in this article is rounded up from a brochure: every figure was read off a machine or carries the date on which it was published.
Describe the material, the contamination and the output you need, and our engineering team will answer with a model and a price range inside one working day. The trial on 10-20 kg of your own material is free, and a measured output more than 5% under the agreed figure leaves the deposit refundable.