CE marked · ISO 9001:2015 · 18-month warranty

· products · By

90 C Friction Washing: What Each Stage Removes

Pre-wash, friction wash and rinse each remove a different contaminant. How a complete line takes a bale to clean flake before the extruder sees it.

A washing line is a sequence of different jobs, not one tank repeated. Pre-wash floats off caps and labels by density, a 90 degree friction washer scrubs adhesive, ink and oil from the flake surface, and a rinse removes the chemicals the wash left behind.

The line then dewaters mechanically before drying thermally, which is far cheaper than evaporating the same water. The target is below 0.5% contamination and below 2% moisture before the material reaches the extruder and its 100 mesh screen.

What each stage removes

  • Wet granulation cuts to 25 to 30 mm while keeping blades cool.
  • Pre-wash separates floating polyolefins from sinking PET.
  • Friction wash at 90 degrees C removes adhesive, ink, oil and soil.
  • A press then a hot-air dryer bring moisture below 2%.
3D render of two green TENGLONG granulating machines with hoppers arranged side by side on a white background
3D render of two green TENGLONG granulating machines with hoppers arranged side by side on a white background. Used here as a visual reference for the friction wash stage of a complete line. Rendering, not a photograph of a customer plant.

Washing is a sequence of different jobs

A washing line is not one tank repeated several times. Each stage removes a different contaminant, and the order matters because later stages work only if earlier ones have done their job. Pre-wash removes loose material, friction washing scrubs what is attached, and rinse removes what the wash left behind.

On the TL-GPL the sequence starts with a wet granulator that reduces bales or film to 25 to 30 mm flakes while water keeps the blades cool. Cutting wet avoids friction heat and keeps labels and caps attached to the flake for the separation stages.

The target before pelletizing is below 0.5% contamination and below 2% moisture. Those two figures determine whether a 100 mesh screen lasts hours or minutes.

Pre-wash: float what can float

Rendered factory floor with red and silver TENGLONG machines and visitors walking through the hall
Rendered factory floor with red and silver TENGLONG machines and visitors walking through the hall. Shown here as production context. Rendering, not a photograph of a customer plant.

The pre-wash tank separates materials by density. Caps and labels from PET bottles are polyolefins and float, while PET sinks. Skimming the floating fraction removes a contaminant that would otherwise melt into the PET and appear as a dark speck.

This stage also wets the flake fully, which helps the friction washer that follows. Dry pockets in a flake bed carry adhesive into the next stage and reduce scrubbing efficiency.

A label remover and cap separator are offered as options for PET duty. They are worth considering when the incoming bales have a high label load, because the flotation stage alone cannot remove labels that are still tightly wrapped.

Friction washing: heat and mechanical scrubbing

The friction washer runs at 90 degrees C and scrubs the flake surface with high-speed paddles. Heat softens adhesive, and the mechanical action removes it along with ink, oil and fine soil. Caustic dosing is offered as an option for oil and label removal, with pH control.

Temperature is a process setting, not a preference. Too low and the adhesive does not release; too high and some polymers soften and deform, which makes them difficult to dewater. The 90 degree figure is the working point for the materials this line handles.

Surfactant dosing follows the contamination type. Oily industrial film needs a different chemistry from bottle labels, and a line that handles both should be able to change the dosing rather than compromise on one setting.

Rinse, dewater and dry

The rinse stage removes washing chemicals and the dirt they carry. Skipping it may look economical but the residues end up in the melt, where they degrade and discolour the pellets.

A screw press then removes free water mechanically, followed by a three-stage hot-air dryer that brings moisture below 2%. The dryer exhaust is recycled to cut gas consumption by 25%, which is the largest energy-saving feature in the washing section.

The order matters: squeezing before heating is far cheaper than evaporating the same water. A line that tries to dry wet flake with hot air alone spends several times the energy and often misses the moisture target.

Matching washing to the polymer

PET bottle flake needs the full hot wash and float-sink sequence because colour and contamination limits are tight. HDPE containers need less aggressive washing but still need label and adhesive removal.

LDPE film is the difficult case because it is bulky and carries soil. The line uses a wet granulator first, then friction washing, and the dewatering stage has to handle a material that holds water in folds.

Our washing line equipment page describes the individual machines, and the turnkey page explains how they are matched. Reading both makes it clear why a supplier must know the feedstock before quoting a washing section.

What each washing stage removes

Each wash stage removes a different contaminant. The table follows a bale through the tanks and out.

Stage Main action Contaminant removed
Wet granulation Cut to 25-30 mm in water Bulk reduction, cool blades
Pre-wash Float-sink separation Caps and floating labels
Friction wash at 90 C Heat plus paddles Adhesive, ink, oil, soil
Rinse Clean water displacement Caustic and surfactant residues
Press and dryer Mechanical then thermal Water to below 2%

Questions buyers ask about this machine

Q1: Why is friction washing done at 90 degrees C?

Heat softens label adhesive and helps the paddles release ink and oil. The 90 degree figure is the working point for the polymers this line handles. Too low and adhesive remains; too high and some materials soften and dewater poorly.

Q2: What does the pre-wash tank actually separate?

It separates by density. PET sinks while polyolefin caps and labels float, so the floating fraction can be skimmed off. A label remover and cap separator are offered as options when bales carry a heavy label load.

Q3: Why dewater mechanically before drying?

Squeezing water out costs about a third of what evaporating it costs. The screw press removes free water and the three-stage hot-air dryer finishes the job to below 2% moisture, with exhaust heat recovery cutting gas use by 25%.

Q4: Can the same line wash PET bottles and LDPE film?

The stages are the same but the settings and feeding differ. Film is bulky and holds water in folds, so wet granulation and dewatering need more attention. The line should be configured around the intended feedstock, not a nominal throughput.

Further reading on this site: plastic granules production line, PET pelletizing line and plastic recycling equipment.

The rest of this series covers the same equipment from different angles: What a Turnkey Granules Line Actually Includes, Water Use in a Granules Line: 0.8 to 1.2 m3 per Tonne, 280 to 900 kW: Power Planning for a Turnkey Line and A Granules Line That Grows from 500 to 3,000 kg/h.

About the author

Zhou Gong (周工) is a recycling machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong, where 30-plus staff work across 18,000 m² and 12 machine platforms covering 100 to 3,000 kg/h. If the rinse is skipped, the chemicals removed in the wash come back in the melt. Every figure used here has been measured on a machine or taken from a dated published source, not from a brochure.

Send the material form, the contamination level and your target output to our engineering team and you get a model and a price range within one working day. A test run on 10–20 kg of your own material is free, and if the measured output misses the agreed figure by more than 5%, the deposit is refundable.

Related reading

العربيةAR