The published specific energy for the TL-FK is 0.26 to 0.36 kWh/kg, the lowest figure in our range. It describes the extrusion and pelletizing line under a stated reference condition, not a complete washing plant, and it assumes a force-fed screw running steadily.
Melting the polymer takes the largest share, but moisture is the biggest avoidable cost: each 1% of water costs roughly 3% of capacity. Filtration and water ring cutting add the rest, and a melt pump can stabilise die pressure as the screen loads.
Where the kilowatts go
- Melting and fusion dominate, helped by the pre-heat and moderate-shear screw.
- Each 1% of moisture costs about 3% of capacity.
- A loading screen raises pressure and motor load.
- Compare suppliers only on the same material, moisture and scope basis.

The number and what it excludes
The published specific energy for the TL-FK is 0.26 to 0.36 kWh/kg, the lowest figure in our machine range. That number describes the extrusion and pelletizing line under the reference condition, not the whole plant from bale to bag.
The reference conditions matter. Output figures are stated for LDPE film at 85% bulk density with 3% moisture, and specific energy is measured over a steady run. A wetter flake, a finer screen or a different polymer moves the number.
Buyers who compare machines on specific energy should confirm that the figures use the same basis. A number measured on clean pellets is not comparable with one measured on washed flake carrying surface water.
Melting the polymer

The largest share of energy goes into raising the polymer from feed temperature to melt temperature and supplying the heat of fusion. Flake has an advantage here: it has already been processed once, and a pre-heating section uses the early barrel length to bring it up gradually.
The 90 to 250 kW IE3 main motors on the three TL-FK models are sized for the screw diameter and the expected throughput. A motor running consistently near its limit suggests either a feed problem or a more contaminated material than the line was specified for.
Screw design contributes to the low figure. A 28:1 to 32:1 L/D with a wear-resistant 38CrMoAlA screw melts at moderate shear, and the force feeder keeps the flights full so each revolution does useful work.
The moisture penalty
Water in the feed is the biggest avoidable energy cost. Each 1% of moisture costs roughly 3% of capacity, because energy goes into heating and vaporising water instead of polymer. The two vacuum vents remove that water before the compression zone, but they do not make it free.
A mechanical dewatering press ahead of the extruder uses far less energy than evaporating the same water in the barrel. That is why our turnkey line pairs a screw press with a three-stage hot-air dryer and recycles the dryer exhaust to cut gas use by 25%.
The practical message is to measure moisture at the feeder. A figure from the washing line does not account for water picked up on a conveyor or in a storage silo.
Filtration and cutting
A screen pack that is loading raises melt pressure and therefore motor load. The double-piston changer on the TL-FK is sized by dirt load, and an oversized pack costs more to heat but holds pressure longer. The balance is found in a material trial.
Water ring die-face cutting at 2.5 to 4 mm adds the cutter and dewatering energy. The published result is pellet moisture below 0.3%, which avoids the downstream thermal drying that a wetter pellet would require.
An optional melt pump for plus or minus 0.4% pellet weight adds a small load but stabilises die pressure as the screen loads. On a long campaign the stability is worth more than the extra kilowatts.
Using the figure in a business case
Multiply the specific energy by the local tariff and by the expected annual output, then add the moisture penalty for your actual feedstock. That produces a number that can be compared with a quotation rather than a brochure figure.
Include screen changes and downtime in the calculation. A line with slightly higher specific energy but a much longer screen life can consume less energy per tonne of saleable pellets, because it spends less time restarting.
Ask for the figure from a trial on your own material. Our factory test procedure records output, melt pressure, melt temperature and kilowatt-hours every minute on a four-hour run, which gives enough data to build a real operating model.
Where the energy is spent
Specific energy is the sum of a few identifiable loads. The table breaks the published 0.26 to 0.36 kWh/kg into where it is spent.
| Load | What drives it | Control |
|---|---|---|
| Melting and fusion | Polymer type, feed temperature | Pre-heat and screw design |
| Moisture | Each 1% costs about 3% capacity | Vents, then dewatering press |
| Filtration | Pressure as the screen loads | Pack size by dirt load |
| Water ring cutting | 2.5-4 mm die-face cutting | Cutter and dewatering |
| Reference figure | 0.26-0.36 kWh/kg | Measured on customer material |
Questions buyers ask about this machine
Q1: What specific energy does a flakes pelletizing line use?
The TL-FK publishes 0.26 to 0.36 kWh/kg, the lowest figure in our range. It is measured on the extrusion and pelletizing line under the stated reference condition, not on a complete washing plant.
Q2: How much does moisture raise energy use?
About 3% of capacity for each 1% of water in the feed. The two vacuum vents handle up to about 4% surface moisture; above that, a mechanical press is cheaper than evaporating the water in the barrel.
Q3: Does a finer screen increase energy use?
Yes, because pressure rises as the pack loads and the motor works harder. The changer is sized by dirt load to keep the interval reasonable. A melt pump can hold die pressure steady as the screen fills.
Q4: Can I compare specific energy between suppliers directly?
Only if the basis matches. Check the polymer, moisture, screen pack and whether the figure covers the whole plant or only the pelletizing line. A number measured on clean pellets is not comparable with one measured on washed flake.
Where this fits in the wider range: flakes pelletizing machine and plastic granules production line.
Read next, if the same model is going on your line: Why Flake Starves a Screw and How Force Feeding Fixes It, Running 4% Moisture Flake Without a Separate Dryer, 80 or 100 Mesh? Size the Screen by Dirt Load and 24/7 Flake Pelletizing: The Screen and Blade Rhythm.
About the author
Zhou Gong (周工) builds recycling lines at TENGLONG Plastic Machinery, a factory in Linyi, Shandong, with 18,000 m² of floor area, 30-plus staff and 820-plus lines delivered to 46 export markets. Energy comparisons mean nothing unless the reference material and moisture are written down. The numbers in this article come from test runs and from dated published sources, not from a sales sheet.
If you want a recommendation rather than a catalogue, send the material form, the contamination level and the target output. We return a model and a price range within one working day, and the test run on 10–20 kg of your own material is free before the balance is paid.