Summary: A specification sheet only helps if you know what each line is really promising. This guide decodes the published TL-UW underwater pelletizer data field by field: the 300–2,000 kg/h output figure and the LDPE film basis it is measured on, the two motor ratings printed for every model, the 1.2–3 mm die-hole range with a ±0.15 mm pellet tolerance, the 3–8 bar pressurised water chamber, the 40–90 °C process water range, cooling flows of 18 to 35 m³/h, and the 60 mesh filtration loop that keeps make-up water under 0.5 m³/h. Each figure is followed by what it depends on, how to judge it against your own feedstock, and where the published range stops and your confirmed test data begins.

Read the basis line before the headline number
The headline on the TL-UW page is 300–2,000 kg/h. The line printed immediately under it is the one that makes the number usable: output figures refer to LDPE film at 85% bulk density with 3% moisture, and actual output depends on feedstock, flake size and filtration. Without that basis, kg/h is a headline, not an engineering value.
Three adjustments move the published figure once your material is on the table. Bulk density changes how much the screw has to compress per kilogram. Moisture changes the energy in the melt and the drying load behind it. Flake size and contamination decide which screen pack you can run, and a tighter pack cuts output and raises melt pressure. A plant running dirty regrind at 500 kg/h and a plant running clean flake at the same screw speed are not the same machine, even though the model name is identical.
What to ask before you accept any output figure
- Ask what the figure is based on — LDPE film, 85% bulk density, 3% moisture is the published basis, and it is printed on the page.
- Ask what it is measured on — a four-hour factory test on your own material logs output, melt pressure, melt temperature and kWh every minute.
- Ask what is excluded — screen pack condition, flake size and contamination level are named as variables, not rounding.
For the published family band and the mechanical details behind it, see the TL-UW underwater pelletizer product page. The factory test procedure behind the confirmed figures is described on how every line is factory tested.
Read the three models as a capacity ladder
The published output is a band per model, not one number: TL-UW-300 at 300–500 kg/h, TL-UW-600 at 700–1,100 kg/h and TL-UW-1000 at 1,400–2,000 kg/h. Notice that the bands leave gaps — roughly 500 to 700 kg/h, and 1,100 to 1,400 kg/h, are not covered. Our engineering reading is that the band is set by the extrusion package and the screen pack rather than by the pelletizing chamber, so a plant whose real output lands in a gap usually runs the larger chamber with a smaller screw, or accepts the top of the smaller band.
Pellet size is banded by model as well: 1.5–3 mm for TL-UW-300, 1.2–3 mm for TL-UW-600 and 2–3 mm for TL-UW-1000. If your customer specification names a single diameter, the model choice narrows immediately, and a die plate change becomes a routine twenty-minute job rather than a production stop.
Two numbers on the same table decide how the machine sits in your building. Footprint runs from 3.4 × 1.9 × 2.2 m for the smallest model to 4.6 × 2.3 × 2.6 m for the largest, and shipping weight from 2.8 t to 5.4 t. Add the space needed to pull the water chamber for a die change and the service access in front of the dryer. Full platform comparisons are in all 12 platforms compared in one table.
Motor ratings answer three different questions
Each model prints two motor figures — 11 kW + 5.5 kW, 22 kW + 7.5 kW, 45 kW + 15 kW — and the technical data block labels the pair as cutter 11–45 kW and water pump 5.5–15 kW. So the first number answers how hard the cutting head works and the second answers how much water has to be moved through the chamber and the heat exchanger. The screw drive is quoted with the extrusion package rather than in this table, which is why a full line total is the sum of three motor groups plus the dryer and conveying auxiliaries.
Do the watts-per-kilogram calculation yourself
The useful arithmetic is watts per kilogram of output. At the published bands, the cutter rating works out at roughly 23 W per kg/h on TL-UW-300 and 32 W per kg/h on TL-UW-1000. Higher specific cutter power usually means a higher die-hole count and a longer strand being cut — more cutting work, not waste. The water pump rating tracks the published cooling flow of 18, 26 and 35 m³/h, so pump capacity and cooling duty stay matched as you climb the ladder.
Drive package on the rest of the line is specified elsewhere: IE3 motors, ABB ACS380 or Danfoss FC51 drives and a Siemens PLC with a 7–10 inch HMI. That matters when you write the electrical single-line diagram for the plant rather than the machine only. If you are comparing platforms on drive architecture instead of on cutting, read single screw versus twin screw granulator first.
Pellet size, tolerance and what the die face guarantees
The published pellet specification is 1.2–3 mm with a tolerance of ±0.15 mm, cut through die holes of the same 1.2–3 mm range and typically 60 to 400 holes in number, with knives passing the die plate at 1,500–4,000 rpm. Judge that tolerance against your own use. On a 2 mm nominal pellet, ±0.15 mm is roughly ±7.5% — comfortable for a dosing screw or a compounding blend, tighter than you want for an optical-grade inspection table.
One option changes the whole size story
Without a melt pump, die pressure follows screen condition and pellet size drifts 0.1–0.2 mm — the same order as the whole tolerance band. With a melt pump, pressure holds within ±0.3% and a screen change no longer disturbs the cut. If your customer writes a pellet diameter onto the purchase order, that option is worth pricing rather than arguing about later.
Two supporting details tell you how hard the machine is to live with. The die is held by a hydraulic die clamp with a quick-release water chamber, so the published die-plate change takes 20 minutes. And die-hole blockage detection with automatic cutter retraction is part of the control system, which means a blocked hole is stopped before it damages the face.
The water circuit is a specification, not a detail
Water is the working medium, so its numbers carry more meaning than on a dry pelletizer. The die face sits inside a sealed chamber held at 3–8 bar, and the circulating water is kept between 40 and 90 °C by a plate heat exchanger, set per polymer recipe. For bottle-grade PET the published range is 70–85 °C: colder water shocks the surface into amorphous, sticky pellets that block the dryer, hotter water deforms the pellet in the silo. PE runs cool.
Do the circulating-flow arithmetic yourself
At the mid-point of the TL-UW-600 band, the published 26 m³/h works out to roughly 29 litres of circulating water per kilogram of output. That is the number that sizes your pump, your heat exchanger and your pipework, and it is also the number that tells you how much heat the loop has to carry away.
Water consumption is much smaller than circulation because the loop is closed. Filtration is 60 mesh and published make-up is under 0.5 m³/h, while circulating flow runs at 18–35 m³/h. Filters are cleaned weekly, so your utility cost is filtration media plus treatment plus a small make-up line, not a water bill proportional to output. If you are mapping the full plant, compare the same way against the washing line equipment and the auxiliary equipment packages.
What the numbers do not guarantee
Every figure above is a published reference range for the machine family. It is not a guaranteed value for one individual unit. Real output, specific energy and pellet quality are set by the incoming material, its moisture and contamination level, and the screen pack fitted — which is exactly why the factory writes confirmed numbers onto the quotation after a four-hour test run on the customer’s own material, and ships the PLC-logged report with the machine.
Three commercial lines travel with the specification. Lead time is 30–40 days, warranty is 18 months from commissioning with three years of spare-parts availability, and the indicative price is US$62,000–160,000 FOB Qingdao for the base configuration, excluding freight, installation and local duties. Minimum order is one set.
One last reading habit. The published electrical supply is 380–440 V, 50/60 Hz, three-phase, and the machine is CE marked with a Declaration of Conformity under an ISO 9001:2015 quality system. If your plant runs on something else, that is a plant project, not a machine option. Send the material, the feed form and the target output through the quotation request form and the configuration comes back within one working day.
| Published parameter | Figure on the TL-UW page | What it actually depends on | How to judge it for your material |
|---|---|---|---|
| Output | 300–2,000 kg/h (TL-UW-300 / 600 / 1000: 300–500, 700–1,100, 1,400–2,000 kg/h) | Feedstock, bulk density, moisture, flake size, screen pack | Compare against the published basis (LDPE film, 85% bulk density, 3% moisture); confirm on a four-hour factory test |
| Drive power | Cutter 11–45 kW + water pump 5.5–15 kW per model | Die-hole count, hole diameter, cutter rpm, circulating cooling flow | Work out watts per kg/h; check the screw drive, quoted with the extrusion package |
| Pellet size | 1.2–3 mm, tolerance ±0.15 mm; die holes 1.2–3 mm, 60–400 holes | Die geometry, cutter rpm, melt temperature, screen condition | Compare ±0.15 mm with your own size specification; add a melt pump if size is contractually fixed |
| Cutter speed | 1,500–4,000 rpm | Pellet diameter, melt viscosity, die-hole count | A slower cut suits larger pellets; a faster cut suits smaller ones and raises specific cutter power |
| Water pressure and temperature | 3–8 bar chamber; process water 40–90 °C | Polymer family, pellet size, melt temperature | Use 70–85 °C for bottle-grade PET and a cooler band for PE; confirm the recipe with the supplier |
| Cooling flow and make-up | 18 / 26 / 35 m³/h circulating; 60 mesh filtration; make-up under 0.5 m³/h | Model size, circulating loop design, fines loading | Size pipework and heat exchanger on the circulating figure, not the make-up figure |
| Footprint and weight | 3.4 × 1.9 × 2.2 m / 2.8 t up to 4.6 × 2.3 × 2.6 m / 5.4 t | Model size, service access, die-change route | Check slab loading, crane access and the space needed to pull the chamber for a die change |
Frequently asked questions
Q1: What exactly does the 300–2,000 kg/h output figure on the TL-UW page mean?
It is the published output band for the TL-UW family, measured on LDPE film at 85% bulk density with 3% moisture. Real output moves with feedstock, flake size and filtration, so the figure to work with is the one confirmed during a four-hour factory test run on your own material, with output, melt pressure, melt temperature and kWh logged every minute.
Q2: Why are two motor figures published for each underwater pelletizer model?
Each model lists two ratings covering the cutter and the water pump, published as 11 kW + 5.5 kW for TL-UW-300, 22 kW + 7.5 kW for TL-UW-600 and 45 kW + 15 kW for TL-UW-1000. The screw drive is quoted with the extrusion package rather than in this table, so a full line total is the sum of three motor groups plus the dryer and conveying auxiliaries.
Q3: How tight is the pellet size tolerance, and what can make it drift?
Published pellet size is 1.2–3 mm with a tolerance of ±0.15 mm. Die holes are 1.2–3 mm and typically 60–400 in number, and the cutter runs at 1,500–4,000 rpm. Without a melt pump, die pressure follows screen condition and pellet size drifts 0.1–0.2 mm, which is the same order as the tolerance band itself.
Q4: What do the 3–8 bar chamber pressure and the 40–90 °C water range control?
Pressure is why the cut is clean: the die face sits inside a sealed chamber held at 3–8 bar, so the melt is sheared under water instead of in air. Temperature decides whether the pellet survives the quench: the plate heat exchanger holds process water between 40 and 90 °C, with 70–85 °C used for bottle-grade PET, because cold water produces amorphous, sticky pellets.
Q5: Which specification numbers are guaranteed and which are reference ranges?
All figures on the product page are published reference ranges for the machine family, not guarantees for one unit. Output, specific energy and pellet quality are set by your material, its moisture and contamination level, and the screen pack fitted. Confirmed values are written onto the quotation after a four-hour factory test run on your own material, and the PLC-logged report ships with the machine.
Engineer’s note
I read a spec sheet the way I read a drawing: every figure should come with the reason behind it. When I quote an output band, the basis travels with it, because a kg/h figure without feedstock and moisture says very little. Our screws are 38CrMoAlA, nitrided in-house to a 0.5–0.7 mm case at HV 900–1000 and straightened to 0.03 mm runout, and barrel, screw, gearbox and frame are aligned to 0.05 mm. A tight tolerance cannot survive a loose machine.
Engineering note: the numbers on this page are our own published reference ranges for the machine family, not a specification guarantee for any individual unit. Final output, specific energy and pellet quality are set by the incoming material, its moisture and contamination level, and the screen pack fitted. We write the confirmed figures onto the quotation after a factory test run on your own material.
Who wrote this
Zhou Gong (周工) is a senior plastic machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong. The factory was registered as Linyi Hedong District Tenglong Plastic Machinery Factory on 7 June 2016 and grew out of a screw and barrel workshop, so his work is rooted in the parts that decide whether a granulator holds output: screw geometry, nitriding case depth, barrel alignment and melt filtration. He prepares the technical specification for customer quotations, reviews the four-hour factory test data before shipment, and runs commissioning support on site. Screws are nitrided in-house to a 0.5–0.7 mm case at HV 900–1000 and straightened to 0.03 mm runout over the full length; barrel, screw, gearbox and frame are aligned to 0.05 mm before the test run.
Figures quoted here are engineering reference ranges published on our own product pages, not guaranteed values for any specific machine. Real output, specific energy and pellet quality depend on the incoming material, its moisture and contamination level, and the screen pack fitted. Final values are written after a factory test run on the customer’s own material, and the PLC-logged test report ships with the machine. For a quotation that reflects your material, send the feed form, contamination level and target output and a configuration comes back within one working day.
If you want the specification read against your own material, send the feed form, the contamination level and the target output to the quotation request form and we will return a TL-UW configuration, with the confirmed figures written onto the quotation, within one working day.