Summary: An underwater pelletizer is priced per machine, but it should be judged per tonne. This article builds a cost model you can recalculate with your own numbers: the formula for cost per tonne, a worked example at the mid-point of the TL-UW-600 band running at 900 kg/h, and a sensitivity table that shows which lever actually moves the result. Melt energy comes from the published 0.26–0.50 kWh/kg band, the published cooling and make-up figures of 18–35 m³/h circulating and under 0.5 m³/h make-up size the water cost, and the published US$62,000–160,000 price range sets the capital recovery term. Every input is labelled as a published figure or an assumption you replace, so the model stays defensible when you take it to a buyer.

Start from output per hour, not from the machine price
Machine price and cost per tonne answer different questions, and only the second one reaches a purchasing decision. A TL-UW-600 sits in the published family range of US$62,000–160,000 FOB Qingdao, and it produces 700–1,100 kg/h. Which model number you need depends on your material, your shift pattern and your utility tariffs — the published band and the background on price sit on what a plastic granulator costs.
So build the model from one hour of production and divide. Take the mid-point of the output band for the model you plan to run, and work out what one hour of running costs: electricity, water and heat, drying and conveying power, labour, consumables, and the share of capital that one hour consumes. Multiply the hourly cost by the tonnes per hour and you have the number to compare against a strand or water ring line. Where the platforms differ mechanically is set out in water ring versus strand versus underwater.
One rule before you start: every line in the model must be either a published figure or an assumption you can replace with your own. Published figures come from the TL-UW underwater pelletizer page and from our published energy band of 0.26–0.50 kWh/kg. Everything else — your tariff, your wage rate, your run hours — is an input, not a fact.
The formula, bucket by bucket
Cost per tonne is the sum of seven buckets divided by tonnes produced in the same period. Written out, the core term is cost per tonne = (total hourly cost ÷ hourly output in kg) × 1,000.
The seven buckets and what belongs in each
- Melt energy — specific energy (kWh/kg) × 1,000 kg per tonne × electricity tariff (per kWh).
- Water and heat — make-up volume (m³) × treatment and disposal rate, plus the energy used to hold the loop at 40–90 °C.
- Drying and conveying power — cutter, water pump, centrifugal dryer and pneumatic transport, converted from nameplate kW and a load factor.
- Labour — operators per shift × hours run × loaded cost per operator hour, divided by tonnes.
- Consumables — screen packs, knives, seal kits, filter media and water treatment, per kilogram.
- Capital recovery — machine price divided by amortised operating hours, converted to a per-tonne figure.
- Overhead, QC and packaging — quality checks, bags or bulk bags, plant overhead allocated to the line.
Run the model for a full year instead of one hour and the capital and overhead terms change, because they are divided by annual tonnes rather than hourly tonnes. That is why run hours appear as a sensitivity lever later, and why the same machine can be cheap per tonne at eight thousand hours and expensive at three thousand.
A worked example at 900 kg/h
Take the mid-point of the TL-UW-600 band, 900 kg/h, an eight-thousand-hour year, and the assumptions below. Replace them with your own; the structure does not change.
Seven lines of arithmetic you can redo in a spreadsheet
- Melt energy — 0.50 kWh/kg at the top of the published band × 1,000 kg = 500 kWh per tonne × US$0.09 per kWh = US$45.00 per tonne.
- Make-up water — 0.5 m³/h published make-up at 900 kg/h = 0.56 m³ per tonne × US$2.50 per m³ = US$1.40 per tonne.
- Cutter, pump, dryer and conveying — published 22 kW + 7.5 kW nameplate at a 70% load assumption gives about 21 kWh/h = 23 kWh per tonne = US$2.10 per tonne.
- Labour — two operators per shift at US$5.50 loaded per hour = US$11.00 per hour = US$12.20 per tonne.
- Consumables — screen packs, knife sets, seals and filter media at an illustrative US$0.012 per kg = US$12.00 per tonne.
- Capital recovery — US$95,000 illustrative machine cost amortised over five years at 8,000 h/yr = US$2.38 per hour = US$2.64 per tonne.
- Overhead, QC and packaging — an assumed US$25.00 per tonne for inspection, bags and line overhead.
Total: about US$100 per tonne at 900 kg/h. At the bottom of the published energy band, 0.26 kWh/kg, the melt energy term falls to about US$23 and the total lands near US$78 per tonne. The band is wide because your material and your tariff are not our variables — which is precisely why we would rather measure it on your pellets than quote it from a brochure.
Sensitivity: which lever actually moves the number
A cost model is only useful if you know where to push. On the worked example, melt energy is roughly 45% of the total, so energy dominates. A change of 0.10 kWh/kg — the gap between a clean flake and a contaminated one, or between a cold and a hot recipe — moves the bill by about US$9 per tonne at US$0.09 per kWh. Tariff moves it just as hard: US$0.07 against US$0.12 per kWh is a spread of roughly US$25 per tonne at 500 kWh per tonne.
Consumables are the sleeper, and run hours are the hidden one
Consumables are the sleeper. Doubling screen pack and seal consumption adds about US$12 per tonne, which is where screen-change discipline pays for itself. Capital recovery is the term most often ignored: amortising the machine over five years gives roughly US$2.60 per tonne at 8,000 hours a year and about US$4.20 at 5,000 hours, because annual tonnes fall while the depreciation does not. Labour per tonne stays almost flat if operators per shift do not change, which is why a two-shift schedule protects capital recovery rather than saving wages.
Finally, output quality feeds back into cost. Fines and rejects are not free: they consume the same energy per kilogram, then get sold at a discount or reground. A stable cut is a cost-control measure before it is a quality measure.
What this model deliberately leaves out
Everything above is a conversion cost at the machine. A landed cost needs more: freight, marine insurance, import duty, installation and commissioning, working capital for feedstock and inventory, laboratory quality control, the silo and bagging equipment downstream, and financing. The published price is explicitly indicative FOB Qingdao for the base configuration, excluding freight, installation and local duties, so a CIF or DAP quotation and the local cost stack sit on top of the hourly figures.
Two exclusions can change the ranking of platforms
A DAP shipment removes ocean freight and insurance from your comparison, which narrows the gap to a locally sourced alternative. A dedicated QC bench for optical or medical grades adds cost per tonne that has nothing to do with the pelletizer, so it belongs in the project total rather than in this model. If you are mapping a whole plant, turnkey pelletizing solutions sets out how the pieces are assembled, and the TL-PET food-contact pelletizing line shows the same wet-pellet logic applied to a specific grade family.
How to make this model your own
Six inputs turn the worked example into a quotation you can defend: your material and its bulk density, the moisture incoming, the contamination level, the target output in kg/h, your electricity tariff, and your planned annual run hours. Add the screen pack you intend to run and the labour you already pay. With those, the model above recalculates in a spreadsheet in minutes.
The part we would rather do than argue about is the specific energy term. A four-hour factory test on your own material records output, melt pressure, melt temperature and kWh every minute, and that trace is what turns 0.26–0.50 kWh/kg from a published band into a measured figure. Send the feed form, the contamination level and the target output through the quotation request form and we will come back with a configuration and a costed tonne within one working day.
| Cost driver | Value in the worked example | Swing from a realistic change | Lever you control |
|---|---|---|---|
| Melt energy | 0.50 kWh/kg → 500 kWh/t → US$45.00/t | ±US$9.00/t per ±0.10 kWh/kg | Screen pack choice, melt temperature, feedstock cleanliness, dryer load |
| Electricity tariff | US$0.09/kWh | ±US$12.50/t per ±US$0.025/kWh | Supply contract, time-of-use pricing, running at tariff hours |
| Make-up water and treatment | 0.5 m³/h → 0.56 m³/t → US$1.40/t | +US$0.28/t per extra 0.1 m³/h of make-up | Leak control, filter cleaning, blowdown discipline |
| Cutter, pump, dryer and conveying | 29.5 kW nameplate at 70% load → US$2.10/t | +US$0.70/t per +10% load | Knife condition, dryer loading, conveying distance |
| Consumables | Screen packs, knives, seals, filter media → US$12.00/t | Up to +US$12.00/t if consumption doubles | Screen change interval, knife rotation at 1,000 hours, filter cleaning weekly |
| Capital recovery | US$95,000 over 5 years at 8,000 h/yr → US$2.64/t | +US$1.60/t if run hours fall from 8,000 to 5,000 | Utilisation, shift pattern, machine size selected |
| Overhead, QC and packaging | US$25.00/t | ±US$5.00/t per added inspection step | Sampling plan, bag or bulk-bag format, batch record keeping |
Frequently asked questions
Q1: What goes into the cost per tonne of an underwater pelletizer?
Seven buckets: melt energy, water and heat, dryer and conveying power, labour, consumables such as screen packs and seals, capital recovery, and overhead for QC and packaging. Add them as hourly costs, divide by kilograms produced per hour, then multiply by 1,000 to convert to cost per tonne. The formula is deliberately simple so each line can be replaced with your own figure.
Q2: How much does electricity dominate the running cost per tonne?
Electricity is usually the largest single line. On the published band of 0.26–0.50 kWh/kg, a 1,000 kg/h line burns roughly 500 kWh per tonne at the top of that band, so every 0.10 kWh/kg changes the bill by about US$9 per tonne at a US$0.09 per kWh tariff. Cutting specific energy is worth more than most other levers in the model.
Q3: Does make-up water really matter in a closed-loop water circuit?
Not as a volume, but as a treatment and disposal cost. The published loop uses 60 mesh filtration with under 0.5 m³/h make-up, while circulating flow runs at 18–35 m³/h depending on the model. Make-up is where minerals, polymer fines and additives accumulate, so filtration and blowdown are recurring cost items rather than a water bill proportional to output.
Q4: How many operating hours a year actually make the machine economic?
Capital recovery per tonne is the term that changes. Amortising a mid-range machine over five years gives roughly US$2.60 per tonne at 8,000 operating hours and about US$4.20 at 5,000 hours, while labour per tonne stays almost flat if operators per shift do not change. Below roughly 5,000 hours a year, compare a smaller machine before you sign for a larger one.
Q5: Which costs are deliberately left out of this per-tonne cost model?
Freight, marine insurance, import duty, installation and commissioning, working capital, laboratory QC, silo and bagging equipment, and financing. The published price range of US$62,000–160,000 is indicative FOB Qingdao for the base configuration, so CIF or DAP quotations and all local costs have to be added on top of the hourly operating cost.
Engineer’s note
Cost work starts with the machine’s own behaviour, not with a spreadsheet. I would rather see your material on our line for four hours than take a guess at kWh per kilogram, because energy per tonne is where the arguments start. The PLC records output, melt pressure, melt temperature and kWh every minute during that run, so the number on the quotation is measured on your pellets, not copied from a brochure.
Engineering note: the numbers on this page are our own published reference ranges for the machine family, not a specification guarantee for any individual unit. Final output, specific energy and pellet quality are set by the incoming material, its moisture and contamination level, and the screen pack fitted. We write the confirmed figures onto the quotation after a factory test run on your own material.
Who wrote this
Zhou Gong (周工) is a senior plastic machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong. The factory was registered as Linyi Hedong District Tenglong Plastic Machinery Factory on 7 June 2016 and grew out of a screw and barrel workshop, so his work is rooted in the parts that decide whether a granulator holds output: screw geometry, nitriding case depth, barrel alignment and melt filtration. He prepares the technical specification for customer quotations, reviews the four-hour factory test data before shipment, and runs commissioning support on site. Screws are nitrided in-house to a 0.5–0.7 mm case at HV 900–1000 and straightened to 0.03 mm runout over the full length; barrel, screw, gearbox and frame are aligned to 0.05 mm before the test run.
Figures quoted here are engineering reference ranges published on our own product pages, not guaranteed values for any specific machine. Real output, specific energy and pellet quality depend on the incoming material, its moisture and contamination level, and the screen pack fitted. Final values are written after a factory test run on the customer’s own material, and the PLC-logged test report ships with the machine. For a quotation that reflects your material, send the feed form, contamination level and target output and a configuration comes back within one working day.
Send your material, target output, tariff and planned annual hours to the quotation request form and we will return a configuration with a per-tonne cost model built on your own figures, within one working day.