Summary: A specification sheet only helps if every line arrives with its basis. This guide decodes the published TL-TS twin screw granulator data field by field: the 300–1,500 kg/h output figure and the LDPE film basis it is measured on, the 62.4 / 71 / 93 mm screw diameters behind the 65 / 75 / 95 mm headline, what a 40:1 L/D actually buys in process layout, why the page prints motor power and torque protection but no rpm band, what eight-channel gravimetric dosing at ±0.5% means for batch reproducibility, and how the 190–260 °C barrel zones, the zone-8 vacuum vent and the 60–120 bar melt pump divide the work. Each figure is followed by what it depends on, how it behaves on your recipe, and where the published range stops and your confirmed test data begins.

Start with the output line and the sentence under it
The headline on the TL-TS page is 300–1,500 kg/h. The line printed immediately under it is what makes the number usable: output figures refer to LDPE film at 85% bulk density with 3% moisture, and actual output depends on feedstock, flake size and filtration. Without that basis, kg/h is a claim rather than an engineering value, and a compounding recipe is not LDPE film.
The model bands leave gaps, and the gaps are informative
The published bands are TL-TS-65 at 300–450 kg/h, TL-TS-75 at 600–900 kg/h and TL-TS-95 at 1,100–1,500 kg/h. Roughly 450–600 kg/h and 900–1,100 kg/h are not covered by any model. Our reading is that the band is set by the drive package and by how fast the screw can swallow feed, not by the pelletizer, so a recipe landing in a gap needs either the larger frame with a slower screw or a confirmed band on your own material.
What the sheet does not claim matters as much. It publishes no filled-compound output, and it should not, because adding 70% calcium carbonate or 30% glass fibre changes bulk density, friction and torque demand at once. Read 300–1,500 kg/h as the unfilled-melt reference and let the factory test define your compounding figure. The platform context sits in all 12 platforms compared in one table, and the machine itself on the TL-TS twin screw granulator product page.
L/D 40:1 and the diameter that decides the rest
L/D is barrel working length divided by screw diameter. The published figure is 40:1, with 44:1 optional. That ratio is not a quality mark; it is a statement about how many process stages fit on one shaft and how long material stays inside the machine.
Where the length actually goes
At 40:1 a 62.4 mm screw gives roughly 2.5 m of working length, and a 93 mm screw roughly 3.7 m. That length has to carry the feed port, the side feeder positions, the melting zone, the kneading zone, the vacuum vents, the filtration position and the die. Diameter sets the melt capacity and the torque the gearbox must carry; L/D sets how many things you can do in one pass. That is why 40:1 is the sensible default for a compounding machine and why going to 44:1 is a process change rather than free capacity.
The extra length of a 44:1 barrel adds shear exposure and residence time. It helps when the recipe needs more devolatilisation or more mixing stages, and it costs you when the polymer is heat-sensitive, because the same shear now happens over a longer barrel at a higher melt temperature. Note also that the header rounds the diameters to 65 / 75 / 95 mm while the model table gives the real figures: 62.4 / 71 / 93 mm.
Co-rotating and segmented: what the screw set actually buys
The published machine is a co-rotating design with segmented screws: conveying, kneading and reverse elements configurable per recipe, with elements that are interchangeable. In engineering terms, the screw set is not a consumable to be ordered later — the screw set is part of the specification, and the same machine can produce a different result with a different element layout.
Wear metallurgy is part of that specification. The published options include bimetallic barrel sleeves and PM-HIP screw elements for abrasive fillers. A calcium carbonate and talc filled PP recipe and a 30% glass fibre reinforced PA6 recipe do not share wear parts, and the page is explicit that the frame and drive can be shared while the screw configuration, barrel metallurgy and wear parts differ. Most buyers keep one screw set per product family and swap in 4–6 hours.
Self-wiping geometry is a throughput fact. Co-rotating twin screws have no dead corners, so the material left behind after a colour change is small. Our published comparison puts the colour change at about 40 minutes on a twin screw against 2–3 hours on a single screw. That is a scheduling number, and it changes the economics of short runs and small batches before it changes anything about pellet quality. The background on that comparison is in single screw versus twin screw granulation.
Torque, speed and the numbers the page does not print
The drive is published as 90–315 kW IE3 — 90 kW on the 65 mm machine, 160 kW on the 75 mm and 315 kW on the 95 mm — and the protection package is listed as a torque limiter and a melt-pressure trip that protect the gearbox on a cold start. Those two facts say more about how the machine is meant to run than a speed range would.
Why the absence of an rpm band is deliberate
For a co-rotating twin screw, output is set by the feed rate and, where one is fitted, by the melt pump. rpm sets shear rate and mixing intensity, not output. Torque sets the ceiling on what the screws can feed and how much filler they can smear. So read three things together: motor kW, the torque limiter setpoint, and the melt pressure trend. A 75 mm machine at 160 kW sitting on its torque limit is running at full specific energy, and the failure mode is heat, not throughput.
The numbers that belong next to the motor. Barrel zones are water-cooled to hold 190–260 °C across six independently cooled zones, with deep-groove cooling bores and independent water circuits per zone. The melt pump builds 60–120 bar for a stable die feed. Torque at a given rpm is what sets how much filler can be dispersed without exceeding the temperature limit, and that relationship — not the headline kilowatt figure — is what a compound actually needs.
Dosing, venting and the options that shape the recipe
Feed control is published as eight-channel gravimetric dosing, each channel within ±0.5%, with recipe management and batch traceability on a Siemens S7-1500 PLC with a 10-inch HMI. That ±0.5% is a per-channel dosing accuracy, not a batch-to-batch colour tolerance, and keeping the two apart is the first thing to get right when you read a compound specification.
Each side feed is a recipe decision, not a fitting. Two side feeders and a liquid injection port are published. The side feeder takes talc, glass fibre and CaCO3; the liquid injection port takes silane, oil or flame retardant. The point of feeding filler sideways is that it enters a partly molten carrier, so it gets wetted instead of dropped into dry powder. Loss-in-weight refill with a vacuum loader per component is the published option that keeps those eight channels supplied.
Filtration decides what a recipe can survive. The published filtration is a hydraulic screen changer or a melt pump with a screen pack. Unfilled compounds run a 60–80 mesh pack; highly filled grades may run a melt pump instead and skip the screen entirely. At the exit the published pellet size is 1.5–4 mm, cut either by underwater pelletizing at 1,500–3,500 rpm with a centrifugal dryer bringing surface moisture below 0.2%, or by strand pelletizing — both on the same frame.
What the sheet leaves to the test run
Every figure above is a published reference range for the machine family, not a guarantee for one unit. Real output, specific energy and pellet quality are set by the incoming material, its moisture and contamination level, and the screen pack fitted. That is exactly why every unit runs 24 hours no-load and then 4 hours on your own material, with output, melt pressure, melt temperature and kWh logged every minute, and why the confirmed figures are written onto the quotation. The procedure is on how every line is factory tested.
Three commercial lines travel with the specification. Footprint runs from 9.5 × 2.2 × 2.6 m at 6.5 t to 13.5 × 2.8 × 3.0 m at 14.5 t, supply is 380–440 V, 50/60 Hz, three-phase, and the published lead time is 35–45 days with an 18-month warranty and a minimum order of one set. The indicative price is US$38,000–128,000 FOB Qingdao for the base configuration.
Before you freeze the layout, fix the terms the sheet leaves open: your filler load, the moisture in that filler, the target pellet size, and whether the site can take a 14.5 t machine on its slab. Selection guidance by material is in granulator selection by material, and the vocabulary is in the pellets and feedstock glossary. Send the recipe and the target output through the quotation request form and a configuration comes back within one working day.
| Published line | Figure on the TL-TS page | What it depends on | How to judge it for your recipe |
|---|---|---|---|
| Output | 300–1,500 kg/h; TL-TS-65 300–450, TL-TS-75 600–900, TL-TS-95 1,100–1,500 kg/h | Feedstock, bulk density, moisture, flake size, filtration, filler load | Compare against the LDPE basis, note the gaps between bands, then confirm on the four-hour factory test |
| Screw diameter and L/D | 62.4 / 71 / 93 mm (headline 65 / 75 / 95 mm); 40:1, 44:1 optional | Process stages that must fit on one shaft: feed, side feeders, melting, mixing, venting, filtration | Treat 44:1 as a process change for heat-sensitive grades, not as free capacity |
| Main motor and protection | 90 / 160 / 315 kW IE3; torque limiter and melt-pressure trip | Feed rate, filler load, screen condition, cold-start state | Read kW, limiter setpoint and melt pressure trend together; never raise the limiter to stop a trip |
| Specific energy | 0.22–0.35 kWh/kg | Polymer, filler load, melt temperature, venting duty | Use it to estimate the energy term in your cost model, then replace it with measured kWh/kg |
| Dosing | Eight-channel gravimetric, each channel within ±0.5%; recipe management, batch traceability | Bulk density variation, bridging, refill supply, component number | ±0.5% is a dosing accuracy, not a batch colour tolerance; check channel drift batch to batch |
| Filtration and melt pressure | Hydraulic screen changer or melt pump plus screen pack; 60–80 mesh pack for unfilled; 60–120 bar | Contamination level, filler abrasiveness, die pressure stability | A melt pump is the answer for highly filled grades; a screen pack is only viable if the feed is clean |
| Pellet size and cutting | 1.5–4 mm; underwater at 1,500–3,500 rpm with surface moisture below 0.2%, or strand | Die and cutter geometry, quench speed, downstream handling | Underwater suits filled and reinforced grades; strand suits clean, unfilled throughput |
Frequently asked questions
Q1: What does the 300–1,500 kg/h output figure on the TL-TS page actually mean?
It is the published output band for the TL-TS family, measured on LDPE film at 85% bulk density with 3% moisture, and the page states that actual output depends on feedstock, flake size and filtration. It is not a compounding output. The number to design with is the one confirmed during a four-hour factory test on your own material, with melt pressure, melt temperature and kWh logged every minute.
Q2: What does a 40:1 L/D mean on a twin screw, and should I order the optional 44:1?
L/D is barrel working length divided by screw diameter, so 40:1 gives roughly 2.5 m of working length on the 62.4 mm screw and about 3.7 m on the 93 mm screw. That length has to carry the feed, the side feeders, melting, mixing, the vacuum vents and filtration in one pass. 44:1 adds shear and residence time: useful for demanding devolatilisation, costly on heat-sensitive grades.
Q3: Why does the specification sheet give motor power but no screw speed range?
Because on a co-rotating twin screw, rpm is not the output control. Output comes from the feed rate and, where fitted, the melt pump; rpm sets shear rate and mixing intensity; torque sets the ceiling on what the screws can feed and smear. Read 90 / 160 / 315 kW IE3 with the torque limiter setpoint and the melt pressure trend.
Q4: How accurate is the eight-channel gravimetric dosing on this machine?
Each of the eight channels is published as holding its component within ±0.5%, with recipe management and batch traceability handled by the Siemens S7-1500 PLC and a 10-inch HMI. Read that as a dosing accuracy rather than a batch-to-batch colour tolerance: dispersion quality, mixing element layout and melt temperature decide the shade, and the dosing figure only keeps the recipe from drifting in the first place.
Q5: Which published specifications are guaranteed, and which are reference ranges?
All of them are published reference ranges for the machine family, not guarantees for an individual unit. Output, specific energy and pellet quality are set by your material, its moisture and contamination level, and the screen pack fitted. Confirmed figures are written onto the quotation after the four-hour factory test on your own material, and the PLC-logged report ships with the machine.
Engineer’s note
I read a specification sheet the way I read a drawing: every figure should arrive with the reason behind it. A kg/h number without feedstock and moisture says very little, which is why the basis travels with it in our quotations. Our screws are 38CrMoAlA, nitrided in-house to a 0.5–0.7 mm case at HV 900–1000 and straightened to 0.03 mm runout, and barrel, screw, gearbox and frame are aligned to 0.05 mm. A tight tolerance cannot survive a loose machine.
Engineering note: the numbers on this page are our own published reference ranges for the machine family, not a specification guarantee for any individual unit. Final output, specific energy and pellet quality are set by the incoming material, its moisture and contamination level, and the screen pack fitted. We write the confirmed figures onto the quotation after a factory test run on your own material.
Who wrote this
Zhou Gong (周工) is a senior plastic machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong. The factory was registered as Linyi Hedong District Tenglong Plastic Machinery Factory on 7 June 2016 and grew out of a screw and barrel workshop, so his work is rooted in the parts that decide whether a granulator holds output: screw geometry, nitriding case depth, barrel alignment and melt filtration. He prepares the technical specification for customer quotations, reviews the four-hour factory test data before shipment, and runs commissioning support on site. Screws are nitrided in-house to a 0.5–0.7 mm case at HV 900–1000 and straightened to 0.03 mm runout over the full length; barrel, screw, gearbox and frame are aligned to 0.05 mm before the test run.
Figures quoted here are engineering reference ranges published on our own product pages, not guaranteed values for any specific machine. Real output, specific energy and pellet quality depend on the incoming material, its moisture and contamination level, and the screen pack fitted. Final values are written after a factory test run on the customer’s own material, and the PLC-logged test report ships with the machine. For a quotation that reflects your material, send the feed form, contamination level and target output and a configuration comes back within one working day.
If you want the specification read against your own recipe, send the feed form, the filler load, the moisture level and the target output to the quotation request form and we will return a TL-TS configuration with the confirmed figures written onto the quotation within one working day.