CE marked · ISO 9001:2015 · 18-month warranty

· products · By

Water Ring Pelletizer Cost per Tonne of Pellets

A recomputable water ring pelletizer cost per tonne model: energy, water, screen changes, labour and downtime, with sensitivity.

TENGLONG TL-WR water ring pelletizer — product photograph from the TL-WR range

Summary: Anyone can put a cost per tonne on a water ring pelletizer. Very few can show the arithmetic, which is why two quotations for the same machine often land on different numbers. This article builds the model instead of asserting it. Six terms are defined and priced: energy from the published specific energy range, cooling water from the closed-loop make-up rate, screen and knife consumables, labour at your own shift pattern, a maintenance allowance, and the amortised machine value. A worked example on a TL-WR-200 at 500 kg/h produces a total you can rebuild line by line, and the sensitivity table then changes one variable at a time to show which inputs actually move the result. The conclusion is not that one number is correct, but that you should be able to reproduce it.

TENGLONG TL-WR water ring pelletizer — product photograph from the TL-WR range
TENGLONG TL-WR water ring pelletizer: one of the configurations in the published TL-WR range.

The formula, written out before any numbers

Cost per tonne is not a single rate. It is the sum of five variable terms that scale with output, plus two fixed terms that scale with time, all divided by the tonnes that reach the bag rather than the tonnes the machine is rated for. Write the model down in this form and every later argument is short.

The seven terms, in the order they bite

Net tonnes per month — rated kg/h × paid hours per month × uptime ÷ 1,000. The uptime factor absorbs screen changes, die cleaning and unplanned stops.

Energy per tonne — specific energy in kWh/kg × 1,000 × tariff per kWh. Our published reference range across the granulator range is 0.26 to 0.50 kWh/kg depending on polymer and moisture, so the whole term is decided by two numbers you control: what you melt, and what you pay per kWh.

Water per tonne — make-up m³/h ÷ (rated kg/h ÷ 1,000) × unit cost per m³. On a 12 m³/h ring the make-up is about 0.36 m³/h, which at 500 kg/h is 0.72 m³ per tonne.

Consumables per tonne — one screen pack cost divided by the tonnes produced between changes, plus the knife set amortised over its life.

Labour per tonne — operators per shift × paid hours × loaded hourly cost ÷ net tonnes. This term is almost fixed, so it punishes low output and rewards high output.

Maintenance and capital — a percentage of machine value per year plus straight-line amortisation of it, both divided by annual net tonnes.

Total cost per tonne is the sum of those seven lines. If a supplier cannot show which line produces which share of their number, the number is an opinion. Background on the equipment price is in what a plastic granulator costs, and the machine data behind these inputs is set out in the TL-WR water ring pelletizer specifications.

A worked example on a TL-WR-200 at 500 kg/h

The example below is deliberately conservative and uses nothing we have not published. Replace the six inputs with your own; the arithmetic stays the same.

  1. Throughput — 500 kg/h, inside the published 300 to 550 kg/h range for the TL-WR-200.
  2. Paid hours — 16 h/day × 26 days = 416 h/month.
  3. Uptime — 92%, absorbing two screen changes per shift plus die inspection.
  4. Net output — 500 × 416 × 0.92 ÷ 1,000 = 191.4 t/month.
  5. Energy — 0.35 kWh/kg × 1,000 × US$0.12 = US$42.00 per tonne. At 0.26 kWh/kg the same tonne costs US$31.20; at 0.50 kWh/kg it costs US$60.00.
  6. Water — 0.36 m³/h ÷ 0.5 t/h = 0.72 m³/t × US$2.00 = US$1.44 per tonne.
  7. Consumables — one screen pack at US$32 every 8 running hours produces 4.0 t, so US$8.00/t; a knife set at US$85 every 400 running hours adds US$0.43/t.
  8. Labour — two operators × 416 h × US$6.50 loaded = US$5,408 per month ÷ 191.4 t = US$28.26 per tonne.
  9. Machine value — take the figure on your own quotation, which sits inside the published US$18,500 to 52,000 band; this example uses US$35,000. Maintenance at 3% per year and five-year amortisation give US$3.51 per tonne.
  10. Total — 42.00 + 1.44 + 8.43 + 28.26 + 3.51 = US$83.64 per tonne.

Everything above is arithmetic, not opinion. The one number that is not a choice is the specific energy, and even that becomes a choice the moment the feed is dried properly or the screen pack is cleaned on time.

What the total is actually made of

Look at the shares and the shape of the problem changes. Energy is about half the total, labour about a third, consumables about a tenth, and water under 2%. Machine value contributes a few dollars. A buyer does not reduce cost per tonne by negotiating the machine price; they reduce it by moving specific energy and getting more tonnes through the paid hours they have already committed to.

Three levers, in order of size

  • Drying beats everything on the energy line. Water in the feed costs twice: it takes heat to vaporise, and it becomes steam voids in the pellet that a customer rejects later. Dry feed moves specific energy down and yield up at the same time.
  • Screen life is a cost lever, not a maintenance chore. Moving from a screen change every 8 hours to every 4 hours doubles the consumables line and, at the same time, lowers uptime. The two effects push in the same direction.
  • Scale is worth more than negotiating. At 300 kg/h the same machine, tariff and labour structure produces US$111.39 per tonne, because the fixed labour and capital terms are spread over 114.8 t instead of 191.4 t. At 500 kg/h it is US$83.64, and at 700 kg/h it is US$71.74. That gap is the largest argument for a bigger machine, and it is why the granulator pricing guide is worth reading before the model is argued about.

Water deserves a note of its own, because the figure is counterintuitive. The loop is closed and returns through a 40 mesh filter, so only about 0.72 m³ per tonne is new water, and at US$2.00 per cubic metre that is US$1.44. Yet the same system carries the 20 to 45 °C band, and exceeding 45 °C is what makes pellets stick together. Water is cheap; water temperature is expensive, because a temperature failure shows up as wet pellets and a jammed screen, not as a utility bill.

Sensitivity: one variable at a time

A model is only useful if you know which input is worth arguing about. The table below changes a single term at a time and keeps everything else at the worked-example value.

What the swings actually mean

Read the third column against the second and three things become visible immediately. Energy dominates, and within energy the polymer and the moisture of the feed matter far more than the tariff: moving from 0.50 to 0.26 kWh/kg saves US$28.80 per tonne, while moving the tariff by US$0.04 saves US$14.00. Labour is the second lever, and it responds to output rather than to negotiation — the difference between 300 and 500 kg/h moves US$18.85 per tonne. Consumables respond to contamination, which is why the contamination level in the enquiry is worth more than a page of motor data.

Downtime sits in a peculiar position. Cutting uptime from 92% to 80% raises the total by only about US$4.80 per tonne, because most of the cost is variable and scales with what is produced. The penalty for downtime shows up in capacity and delivery, not in the cost per tonne headline. A plant that loses 12% of its schedule has quietly bought a 12% smaller machine — the number the sales review should see.

One caveat applies to all of it. Our published specific energy range of 0.26 to 0.50 kWh/kg is a reference range for the machine family, not a guarantee for a particular formulation. The 4-hour factory test run on your own material, logged every minute, replaces the modelled energy term with a measured one. If a quotation does not carry that figure, treat the energy line as an assumption rather than a promise.

Turning the model into your own quote

Six inputs are yours, and only six. Gather them before the conversation starts.

  1. Material and moisture — the polymer grade and the moisture actually measured on the flake, not the nominal figure from the supplier.
  2. Contamination level — the share of fines, the level of inorganic residue, and whether washing happens upstream.
  3. Paid hours and shift pattern — including the operator count you genuinely staff, not the one on the layout drawing.
  4. Electricity tariff — your all-in rate per kWh including demand charges.
  5. Screen and knife service interval — from your existing records, or from our reference consumable cost list.
  6. Target output in tonnes per month — this is the number that decides which of the three models is the right one.

Then run the model twice: once at 500 kg/h and once at 300 kg/h. If the answer changes model, you have found your real constraint, and it is usually throughput or staffing rather than machine specification. If it does not change model, the water ring is comfortably the right platform and the remaining work is commissioning.

If the total per tonne looks wrong for your market, the fastest way to close the gap is usually not a cheaper machine. It is drying, better upstream washing, and running more hours. The TL-UW underwater pelletizer exists for the cases where none of those three are available to you, and the TL-ST strand pelletizing line for the case where the pellet shape itself, rather than the cost, is the deciding factor.

Cost per tonne of pellets on the worked TL-WR-200 example, with the sensitivity of each term. Every input is replaceable; only the published ranges are fixed.
Cost line Base case input Base case per tonne Swing if the input moves What moves it
Energy (extruder + pelletizer) 0.35 kWh/kg at US$0.12/kWh US$42.00 US$31.20 at 0.26 kWh/kg, US$60.00 at 0.50 kWh/kg Polymer, feed moisture, screen pack
Cooling water 0.72 m³/t at US$2.00/m³ US$1.44 US$0.72 at US$1.00/m³, US$2.88 at US$4.00/m³ Ring size, make-up rate, plant cooling
Screen pack and knives Screen every 8 h at US$32, knife set at US$85 US$8.43 US$16.86 at a 4-hour screen interval Contamination level of the feed
Direct labour Two operators × 416 h × US$6.50 US$28.26 US$47.11 at 300 kg/h, US$20.19 at 700 kg/h Paid hours, staffing, output rate
Maintenance allowance 3% of machine value per year US$0.46 US$0.92 on a doubled allowance Machine age, abrasive feed, service quality
Capital recovery US$35,000 over 5 years US$3.05 US$1.61 at US$18,500, US$4.53 at US$52,000 Machine value and annual tonnes
Total cost per tonne 191.4 t/month net output US$83.64 US$71.74 at 700 kg/h, US$111.39 at 300 kg/h Everything above, taken together

Frequently asked questions

Q1: How do you calculate the cost per tonne of pellets from a water ring pelletizer?

Sum seven terms and divide by net tonnes: energy (specific energy × 1,000 × tariff), cooling water, screen and knife consumables, labour, a maintenance allowance, and amortised machine value. Net tonnes are rated output × paid hours × uptime ÷ 1,000. On our worked TL-WR-200 example the total is US$83.64 per tonne, and every line of it can be rebuilt from your own inputs.

Q2: What is the single biggest cost item in water ring pelletizing?

Energy, at roughly half of the total. On the worked example it is US$42.00 per tonne out of US$83.64, because specific energy alone moves between 0.26 and 0.50 kWh/kg depending on polymer and moisture. Labour is second at about a third. Machine value is a few dollars, so negotiating the purchase price does very little for the per-tonne number.

Q3: How much does the cooling water add to the cost per tonne of pellets?

Less than 2%. The loop is closed, filtered through a 40 mesh screen and returned, with make-up of roughly 0.3 m³ per hour on a 10 m³/h ring. At 500 kg/h that is about 0.72 m³ per tonne, or US$1.44 at US$2.00 per cubic metre. The real cost is temperature: above 45 °C pellets stick together, and that shows up as jammed screens, not a utility bill.

Q4: How does screen change frequency change the cost per tonne of pellets?

Directly, and in two directions at once. A screen pack of US$32 changed every 8 running hours costs US$8.00 per tonne at 500 kg/h; changing every 4 hours doubles it to US$16.00 and also cuts uptime, which pushes labour and capital per tonne up. Screen life is a function of feed contamination, which is why the contamination level in an enquiry matters more than any motor figure.

Q5: Does running the machine at higher output really reduce the cost per tonne?

Yes, and the effect sits in labour and capital, not energy. At 300 kg/h the same model works out at US$111.39 per tonne; at 500 kg/h it is US$83.64, and at 700 kg/h it is US$71.74. The difference is the fixed terms spread over more tonnes. If you are comparing a smaller machine running longer against a larger one running shorter, build both into the model.

Engineer’s note

A cost per tonne that arrives without its arithmetic is not worth discussing, so I ask for the six inputs before I give a number. The two that decide most cases are feed moisture and screen life, and both are visible in the 4-hour factory test run, where output, melt pressure and kWh are logged every minute. With our nitrided screw case at 0.5 to 0.7 mm, HV 900 to 1000, the specific energy term stops being a guess and becomes a measurement.

Engineering note: the numbers on this page are our own published reference ranges for the machine family, not a specification guarantee for any individual unit. Final output, specific energy and pellet quality are set by the incoming material, its moisture and contamination level, and the screen pack fitted. We write the confirmed figures onto the quotation after a factory test run on your own material.

Who wrote this

Zhou Gong (周工) is a senior plastic machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong. The factory was registered as Linyi Hedong District Tenglong Plastic Machinery Factory on 7 June 2016 and grew out of a screw and barrel workshop, so his work is rooted in the parts that decide whether a granulator holds output: screw geometry, nitriding case depth, barrel alignment and melt filtration. He prepares the technical specification for customer quotations, reviews the four-hour factory test data before shipment, and runs commissioning support on site. Screws are nitrided in-house to a 0.5–0.7 mm case at HV 900–1000 and straightened to 0.03 mm runout over the full length; barrel, screw, gearbox and frame are aligned to 0.05 mm before the test run.

Figures quoted here are engineering reference ranges published on our own product pages, not guaranteed values for any specific machine. Real output, specific energy and pellet quality depend on the incoming material, its moisture and contamination level, and the screen pack fitted. Final values are written after a factory test run on the customer’s own material, and the PLC-logged test report ships with the machine. For a quotation that reflects your material, send the feed form, contamination level and target output and a configuration comes back within one working day.

Send the polymer, moisture, contamination level and monthly output, and we will return a cost per tonne built on the same model, with the confirmed figures from a test run on your material. Request a costed configuration — one working day.

Related reading

العربيةAR