CE marked · ISO 9001:2015 · 18-month warranty

· products · By

Underwater Pelletizer Problems and Fixes

A symptom-first underwater pelletizer troubleshooting playbook: flat pellets, foam, sticking, wet pellets, water loop losses and wide size spread.

TENGLONG TL-UW underwater pelletizer — product photograph from the TL-UW range

Summary: This is a symptom-first troubleshooting playbook for the TL-UW underwater pelletizer: symptom, then likely cause, then the action that actually fixes it. It covers the six faults that generate most service calls — pellets that come out flat instead of spherical, foam and bubbles in the melt, polymer sticking to the knife and blocking the die holes, pellets arriving above the published 0.1% moisture figure, pellets lost with the circulating water, and a particle size distribution that spreads wider than the ±0.15 mm tolerance allows. Each entry is tied to a published machine figure you can check yourself — 3–8 bar chamber, 40–90 °C process water, 18–35 m³/h circulating flow, 60 mesh filtration, knife checks every 500 hours — and to the PLC trend that shows the fault developing.

TENGLONG TL-UW underwater pelletizer — product photograph from the TL-UW range
TENGLONG TL-UW underwater pelletizer: one of the configurations in the published TL-UW range.

Triage order: stop, protect, then adjust one thing

Before any adjustment, decide whether the line should keep running. A die blockage with knives turning against damaged holes damages the die face, and that is an expensive fault rather than a nuisance. So: stop, protect, then adjust — and change one variable at a time, because a temperature change and a flow change together tell you nothing about which one mattered.

Read the trend before touching the machine

The second habit is to read the trend first. Every unit in our factory runs 24 hours no-load and then four hours on the customer’s material with output, melt pressure, melt temperature and kWh logged every minute. The same logging on your own line turns a vague complaint into a signal: rising melt pressure means the screen pack is closing, drifting kWh means the melt is working harder, falling output with steady pressure means the cut is degrading. The procedure is described on how every line is factory tested.

Then work down the physical order of the process — water circuit, die face, cut, quench, dryer — because a fault earlier in that chain shows up later as a different symptom. A particle size spread that looks like a cutter problem is often a water temperature problem. Start at the published figures for the machine you own: the TL-UW underwater pelletizer specification lists them model by model.

Shape and surface defects: flat, oval, dull pellets

  • Symptom — pellets are oval or flattened instead of round, surfaces are dull rather than glassy, and fines are heavier than the published dust level of below 0.2%.
  • Cause — the cut is happening at the wrong temperature, or with a dull edge. If the water is colder than the polymer needs, the strand is shock-frozen before it can round off; if melt temperature is drifting across the die face, the cut tears instead of shearing. A worn knife reproduces the same symptom with completely different causes behind it.
  • Action — measure the water temperature at the chamber and compare it with the recipe band of 40–90 °C, using 70–85 °C for bottle-grade PET. Then check melt temperature stability on the trend, and check knife condition against the published schedule: knives inspected every 500 hours and rotated every 1,000. Only after those two are right should you change anything else.

Foam, bubbles and an unstable melt stream

  • Symptom — bubbles in the melt, intermittent spitting at the die face, unstable pellet weight and a noisy, irregular cut.
  • Cause — three usual sources. Moisture in the feed turns into steam in the barrel; air is drawn in at the feed opening; and a blocked screen pack makes the melt overheat and gas up before it reaches the die. The third is the one operators miss, because it feels like a temperature problem.
  • Action — dry the feed and seal the feed throat to remove the first two causes. For the third, watch melt pressure on the PLC trace, logged every minute during the factory test: a steady climb while output falls points at the screen pack, and the answer is a screen change rather than a temperature change. Feeding drier material into a fouled screen makes the fouling worse, not better.

Sticking to the knife and blocked die holes

  • Symptom — polymer smears onto the knife and die face, holes block, output falls, and the die-hole blockage detection with automatic cutter retraction starts tripping during a run.
  • Cause — cold or thin water lets the melt smear instead of shear; debris in the circulating loop does the same thing; and a knife that has lost its edge glues material on contact. The published PET guidance is the clearest warning: cold water produces amorphous, sticky pellets.
  • Action — check circulating flow against the published 18, 26 or 35 m³/h for the model, clean the 60 mesh filter, and confirm the blockage detection and automatic retraction are armed rather than bypassed. Then follow the knife schedule: inspection at 500 hours, rotation at 1,000 hours, die plate polish every 2,000 hours. Check the seal kit as well — a full seal change is a two-hour job once a year, and a leaking seal pulls air into the chamber.

Drying results: pellets above 0.1% moisture

  • Symptom — pellets weigh more than expected, stick to each other in the silo, and the measured moisture sits above the published ≤0.1% after the centrifugal dryer figure.
  • Cause — the centrifugal dryer removes surface water, not moisture bound inside the pellet, so a wet pellet is either not a surface problem or not a dryer problem. Three usual sources: the dryer is loaded beyond what the centrifugal stage can throw off; foam arriving with the melt is holding extra water; or the water circuit is running colder than the recipe, so pellets arrive sticky and heavy.
  • Action — compare dryer load with throughput, confirm pellets reach the dryer below 45 °C, and check the heat exchanger is holding its band. Then check the seals, and check whether the melt is foaming upstream. If the pellets are dry on the surface but heavy in the hand, look upstream at the melt, not at the dryer.

Separate surface water from bound moisture

The distinction decides where you look. A hand sample that feels wet points at the loop, the quench temperature and the dryer load. A hand sample that feels dry but still fails the moisture check points at the melt itself — the polymer went in with moisture it never lost. Terms such as surface moisture and bound moisture are defined in the pellets and feedstock glossary, and the moisture target itself depends on the grade you run rather than on the machine.

Water loop losses and a widening particle size spread

  • Symptom — pellets found in the water loop or in the drain, make-up water rising without a leak, and a particle size distribution wider than the published ±0.15 mm tolerance.
  • Cause — losses come from a low water level, an overflow, or fines carried out with the blowdown, and a sudden rise in make-up above the published under 0.5 m³/h usually means the filter is loading with fines, not that the loop is healthy. The size spread has its own causes: die holes wearing larger than nominal, dull cutting edges, inconsistent screen condition, or melt temperature drifting across the face.
  • Action — keep the level steady, clean the filters weekly as the maintenance schedule states, and measure the make-up rate against the published figure. For size, check the die-hole diameter against the 1.2–3 mm specification, check cutter rpm against the 1,500–4,000 rpm range, and consider the melt pump option if size is contractually fixed: pressure then holds within ±0.3% instead of drifting 0.1–0.2 mm with screen condition. If you are sizing a dewatering step instead of a pelletizing step, the TL-PM plastic pellet mill is the other machine to compare against.
Symptom-first index for the TL-UW: what you see, the most likely cause, the first check, and the corrective action.
Symptom Most likely cause First check Corrective action
Flat, oval or dull pellets; extra fines Water temperature below the recipe band, or dull knife edges Chamber water temperature against the 40–90 °C range (70–85 °C for PET) Restore the recipe band, stabilise melt temperature, re-index or replace knives
Foam, bubbles, unstable pellet weight Feed moisture, air ingress at the feed throat, or a blinded screen pack Feed moisture level and the melt pressure trend on the PLC log Dry and seal the feed, then change the screen pack rather than the temperature
Melt sticking to the knife, holes blocking Low circulating flow, cold water, debris in the loop, or a worn knife Circulating flow against 18 / 26 / 35 m³/h, the 60 mesh filter, retraction function Restore flow, clean the filter, verify blockage detection, rotate knives at 1,000 hours
Pellets above 0.1% moisture, heavy and sticky Dryer overloaded, foam arriving with the melt, or a failed heat exchanger Dryer load against throughput and pellet temperature below 45 °C Reduce load, restore water temperature, check seals and heat exchanger
Pellets lost with the circulating water Low level, overflow, or fines blown out with the blowdown Water level and make-up rate against the published under 0.5 m³/h Restore level, clean filters weekly, reduce blowdown carry-over
Particle size spread wider than ±0.15 mm Worn die holes, dull edges, or screen condition changing die pressure Die-hole diameter against 1.2–3 mm and cutter rpm against 1,500–4,000 rpm Replace or polish the die plate, fit a melt pump if size is contractually fixed

Frequently asked questions

Q1: Why do the pellets come out flat or oval instead of spherical, and what fixes it?

Shape is set at the die face. If the water is colder than the polymer needs, the strand is shock-frozen before it can round off; if the knife edge is dull or the melt temperature drifts, the cut tears instead of shearing. Restore the recipe water band of 40–90 °C, re-index or replace the knives, and hold melt temperature steady before changing anything else.

Q2: What causes foam and bubbles in the melt, and how do you clear them?

Three usual sources: moisture in the feed, air drawn in at the feed throat, and a blocked screen pack that makes the melt overheat in the barrel. Drying the feed and sealing the feed opening remove the first two. The third appears as rising melt pressure on the PLC trend, logged every minute during the four-hour factory test, and calls for a screen change rather than a temperature change.

Q3: Why do the pellets stick to the knife and block the die holes?

Cold or thin water lets the melt smear on the knife instead of shearing. Check the cooling flow against the published 18, 26 or 35 m³/h for the model, clean the 60 mesh filter, and confirm the die-hole blockage detection with automatic cutter retraction is armed. Worn knives also glue: inspect every 500 hours, rotate every 1,000.

Q4: Why does pellet moisture stay above the 0.1% target after drying?

The centrifugal dryer removes surface water, not moisture bound in the pellet. Above the published ≤0.1% after the centrifugal dryer figure, check the dryer load against throughput, confirm pellets arrive below 45 °C, and look for foam arriving with the melt. A leaking seal or a failed heat exchanger also leaves pellets wet and heavy.

Q5: How do I stop losing pellets out of the circulating water loop?

Loss happens when the loop runs dry, overflows, or carries fines out with the blowdown. Keep the level steady, clean the filters weekly as the maintenance schedule states, and watch the make-up rate: the published target is under 0.5 m³/h on a loop circulating 18–35 m³/h. A sudden rise in make-up usually means fines are loading the filter, not that the loop is working well.

Engineer’s note

The trend comes before the toolbag. Our PLC logs output, melt pressure, melt temperature and kWh every minute during the four-hour factory test on customer material, so most faults announce themselves in the trace long before anyone reaches for a screwdriver. Wear parts come next: knives at 500 hours, rotation at 1,000, die polish at 2,000. A worn knife and a dull temperature setting look identical from the discharge chute.

Engineering note: the numbers on this page are our own published reference ranges for the machine family, not a specification guarantee for any individual unit. Final output, specific energy and pellet quality are set by the incoming material, its moisture and contamination level, and the screen pack fitted. We write the confirmed figures onto the quotation after a factory test run on your own material.

Who wrote this

Zhou Gong (周工) is a senior plastic machinery engineer at TENGLONG Plastic Machinery in Linyi, Shandong. The factory was registered as Linyi Hedong District Tenglong Plastic Machinery Factory on 7 June 2016 and grew out of a screw and barrel workshop, so his work is rooted in the parts that decide whether a granulator holds output: screw geometry, nitriding case depth, barrel alignment and melt filtration. He prepares the technical specification for customer quotations, reviews the four-hour factory test data before shipment, and runs commissioning support on site. Screws are nitrided in-house to a 0.5–0.7 mm case at HV 900–1000 and straightened to 0.03 mm runout over the full length; barrel, screw, gearbox and frame are aligned to 0.05 mm before the test run.

Figures quoted here are engineering reference ranges published on our own product pages, not guaranteed values for any specific machine. Real output, specific energy and pellet quality depend on the incoming material, its moisture and contamination level, and the screen pack fitted. Final values are written after a factory test run on the customer’s own material, and the PLC-logged test report ships with the machine. For a quotation that reflects your material, send the feed form, contamination level and target output and a configuration comes back within one working day.

If a fault is not on this page, send the material, the PLC trace and the symptom through the quotation request form and we will work from the same numbers we logged on our own four-hour test runs, with a reply within one working day.

Related reading

العربيةAR